суббота, 6 декабря 2008 г.
как узнать какая мат. плата установлена на сервере под управлением ОС Linux?
воскресенье, 30 ноября 2008 г.
horde. login failed.
В horde.log
HORDE [error] [imp] FAILED LOGIN x.x.x.x to localhost:143[imap/notls] as 'user' [on line 247 of
"/root/horde/imp/lib/Auth/imp.php"]
HORDE [info] [imp] x.x.x.x failed [on line 31 of "/root/horde/imp/login.php"]
2. выполнить /usr/local/psa/admin/bin/mchk -v
проверить работу. если нет - попробовать заменить в /etc/psa-horde/imp/servers.php
'server' => 'localhost', на 'server' => 'IP Address',
четверг, 20 ноября 2008 г.
Использование программного RAID-1 (gmirror) в FreeBSD
Оригинал: http://dreamcatcher.ru/docs/freebsd-raid.html
На английском: http://www.onlamp.com/pub/a/bsd/2005/11/10/FreeBSD_Basics.html
Мною взято с http://www.opennet.ru/base/sys/freebsd_gmirror_raid1.txt.html
Использование программного RAID-1 в FreeBSD
Dru Lavigne
Перевод: Сгибнев Михаил
Вы когда-нибудь нуждались в программном решении RAID на сервере
начального уровня? Возможно, вы хотели бы использовать избыточность,
предоставляемую зеркалированием, на своей рабочей станции не тратя
денег на RAID-контроллер? А может, у вас был уже опыт настройки
программного RAID на UNIX-системах и вы потерпели неудачу?
Начиная с 5.3-Release, в состав FreeBSD входит утилита gmirror(8),
которая позваляет вам более легко создавать решения RAID 1. Хотя
существует учебник по gmirror(8), все равно требуется много вычислений
размеров разделов с помощью bsdlabel или использование дискеты
восстановления имеющейся системы.
Мне кажется, что было бы более разумно настраивать RAID во время
установки системы. Так же, хотелось бы разработать методику, на
которую не влиял бы человеческий фактор, в виде ошибочных расчетов.
После нескольких проб и ошибок, была разработана данная методика,
которая была мною проверена на различных системах и хорошо себя
зарекомедовала. Так же, я получила ценные данные от Поэльа Джакаба
Доидека(Pawel Jakub Dawidek), автора gmirror, в добавок раскрывшего
мне некоторые недокументированные возможности gmirror.
Некоторая подготовка GEOM
Перед тем, как мы приступим к нашим экспериментам, сделаем краткий
экскурс в GEOM. GEOM является модульной дисковой структурой,
появившейся в FreeBSD 5.0. В результате модульной структуры,
появляется возможность создавать программы, способные управлять
дисками. Лучшие примеры - программные реализации RAID, появившиеся в
FreeBSD 5.3:
* gstripe(8) обеспечивает чередование или RAID 0
* mirror(8) обеспечиват зеркалирование/дуплекс или RAID 1
* graid3(8) обеспечивает чередование с контролем четности или RAID 3
Начальная g указывает на то, что эти утилиты пользуются возможностями,
которые предоставляет GEOM.
Обратите внимание, что если вы плохо знакомы с RAID, то Webopedia дает
хорошее определение каждого уровня RAID.
man 4 geom описывает используемые термины, которые включают в себя:
* Провайдер -- Этот объект GEOM появляется в /dev. В этой статье
рассматривается, как создать провайдер, известный как
/dev/mirror/gm0, представляющий mirror/duplex диск.
* Потребитель -- Этот объект получает запросы ввода - вывода. В
примере mirror/duplex, это - два физических диска. Я использую два
IDE диска на отдельных кабелях, обозначенных как /dev/ad0 и
/dev/ad2.
* Метаданные -- При обращении к любому уровню RAID, метаданные
описывают членов массива, их размеры и местоположение, содержат
описания логических дисков и разделов, и текущее состояния
дискового массива.
* mirror/duplex -- RAID 1 содержит одинаковые данные на двух
различных дисках. Другими словами, происходит зеркалирование
данных одного диска на другой. Если оба диска подключены к одному
каналу, то они зеркалированы. Если к разным каналам - то они
работают в дуплексном режиме. Поскольку в режиме зеркалирования
отказ канала приведет к отказу системы, большинство серверов
работают в режиме дуплеска.
Конфигурирование зеркалирования/дуплекса
Если вы собираетесь сделать RAID 1, то не ищите лишних сложностей, а
купите два идентичных (одного производителя и емкости) жестких диска.
Вы можете и не последовать этому совету, но тогда столкнетесь с
некоторыми сложностями и впустую потратите излишек свободного места на
большем диске. Подключите диски как primary master и secondary master.
Перед установкой операционной системы проверьте, что ваш CMOS
распознает оба диска.
Используя ваш любимый инсталляционный метод, запустите установку
FreeBSD любой версии (5.3 или выше). Когда Вы принимаетесь за меню
Select Drives, то должны увидеть ad0 и ad2. Выберите ad0, поскольку вы
будете устанавливать операционную систему на primary master.
С помощью утилиты fdisk удалите любые существующие разделы и выберите
"Use entire disk". На вопрос о меню загрузки, ответьте "Standard MBR".
В редакторе меток диска создайте разделы на ad0 согласно вашим
требованиям. Если есть какие-либо сомнения, то выберите автоматический
режим. После этого выберите устанавливаемые наборы и тип носителя,
после чего установите операционную систему в обычном порядке.
Когда установка завершится, установите ваш часовой пояс, создайте
учетную запись пользователя, установите пароль root, и так далее.
После настройки этих параметров не стоит перезагружаться. Нажмите
Alt-F4 для перехода в режим командной строки. Первой командой, которую
я ввожу, обычно бывает csh, для того, чтобы у меня была оболочка с
историей команд (по умолчанию устанавливается оболочка Bourne).
Создание зеркалирования/дублекса осуществляется вводом следующей
команды:
# gmirror label -v -b round-robin gm0 /dev/ad0
Где gmirror label создает зеркало, функция -v включает режим отладки,
-b round-robin выбирает алгоритм балансировки (в настоящее время это
наиболее быстродействующий алгоритм), gm0 - имя первого зеркала GEOM и
/dev/ad0 указывает на диск, содержащий данные для зеркалирования.
Однако, если вы попробуете выполнить эту команду сейчас, то будете
разочарованы:
# gmirror label -v -b round-robin gm0 /dev/ad0
Can't store metadata on /dev/ad0: Operation not permitted
Это особенность защиты, которая указывает, что диск в настоящее время
установлен для записи и поэтому недоступен. Однако, вы можете обойти
эту проблему цыпленка-и-яйца и временно вынудить
gmirror обойти эту меру, чтобы создать зеркалирование/дуплекс,
устанавливая sysctl MIB:
# sysctl kern.geom.debugflags=16
kern.geom.debugflags: 0 -> 16
Не волнуйтесь, после перезагрузки этот параметр снова примет значение
"0". А теперь выполним:
# gmirror label -v -b round-robin gm0 /dev/ad0
Metadata value stored on /dev/ad0
Все, теперь у нас есть RAID 1.
Так же теперь нам необходимо отредактировать два файла. Первый из них
в настоящее время пуст, используем утилиту echo для того, чтобы внести
в него необходимый параметр:
# echo geom_mirror_load="YES" > /boot/loader.conf
Поскольку в файле /etc/fstab у нас уже содержатся некие данные, то
лучше сделать его резервную копию.
# cp /etc/fstab /etc/fstab.orig
# vi /etc/fstab
Измените каждый ad на gm и вставьте mirror после /dev. Для примера,
/dev/ad0s1a трансформируется в /dev/mirror/gm0s1a. Если вы не делали
дополнительные разделы, то у вас будут устройства ad0s1,
оканчивающиеся на a, b, d, e и f. Необходимо отредактировать каждую
строку.
После внесения всех изменений, проверьте эти файлы еще раз. Будет
очень обидно, если система не загрузится из-за сделанной опечатки.
Обратите внимание, что в некоторых руководствах указано требование к
наличию опции swapoff в /etc/rc.conf. Теперь это не является
необходимым, так же как и использование shutdown -r now вместо reboot.
Теперь, когда вы уверены, что все в порядке, нажмите Alt-F1, извлеките
установочный диск и выйдите из утилиты установки.
Загрузка в режиме зеркалирования/дуплекса
Если вы внимательно смотрите на экран во время начальной загрузки, то
должны увидеть следущие строки:
GEOM_MIRROR: Device gm0 created (id=2125638583).
GEOM_MIRROR: Device gm0: provider ad0 detected.
GEOM_MIRROR: Device gm0: provider ad0 activated.
GEOM_MIRROR: Device gm0: provider mirror/gm0 launched.
GEOM_MIRROR: Device gm0 already configured.
Mounting root from ufs:/dev/mirror/gm0s1a
После монтирования /dev/mirror/gm0s1a система продолжит загрузку. Если
вы допустили опечатку в /etc/fstab, то загрузка остановится и система
будет ждать от вас каких-либо действий. Я забыла вставить mirror,
когда редактировала /etc/fstab:
Mounting root from ufs:/dev/gm0s1a
setrootbyname failed
ffs_mountroot: can't find rootvp
Root mount failed: 6
Manual root filesystem specification:
: Mount using filesystem
e.g. ufs:da0s1a
? List valid disk boot devices
Abort manual input
mountroot>
К счастью, все не так страшно, как выглядит. Сперва просмотрим
доступные дисковые устройства:
mountroot> ?
List of GEOM managed disk devices:
mirror/gm0s1f mirror/gm0s1e mirror/gm0s1d mirror/gm0s1c mirror/gm0s1b
mirror/gm0s1a mirror/gm0s1 ad2s1 mirror/gm0 ad0s1 ad2 acd0 ad0 fd0
Если вы укажете правильное расположение корневой файловой системы, то
система продолжит загружаться:
mountroot> ufs:/dev/mirror/gm0s1a
Mounting root from /dev/mirror/gm0s1a
После входа в систему, исправьте /etc/fstab и перезагрузитесь, после
чего снова войдите в систему и удостоверьтесь, что все файловые
системы примонтированы правильно:
% df -h
Filesystem Size Used Avail Capacity Mounted on
/dev/mirror/gm0s1a 248M 35M 193M 15% /
devfs 1.0K 1.0K 0B 100% /dev
/dev/mirror/gm0s1e 248M 12K 228M 0% /tmp
/dev/mirror/gm0s1f 7.3G 99M 6.7G 1% /usr
/dev/mirror/gm0s1d 248M 196K 228M 0% /var
Утилита df не покажет состояние раздела подкачки, воспользуемся другой:
% swapinfo
Device 1K-blocks Used Avail Capacity
/dev/mirror/gm0s1b 629544 0 629544 0%
Синхронизация дисков
Единственное, что мы еще не сделали, так это не синхронизировали
диски. Это случится автоматически, как только вы вставите второй диск
в зеркало:
# gmirror insert gm0 /dev/ad2
GEOM_MIRROR: Device gm0: provider ad2 detected.
GEOM_MIRROR: Device gm0: rebuilding provider ad2.
Смотрите, что случится:
# gmirror list | more
Geom name: gm0
State: DEGRADED
Components: 2
Balance: round-robin
Slice: 4096
Flags: NONE
GenID: 0
SyncID: 1
ID: 2125638583
Providers:
1. Name: mirror/gm0
Mediasize: 10262568448 (9.6G)
Sectorsize: 512
Mode: r6w5e2
Consumers:
1. Name: ad0
Mediasize: 10262568448 (9.6G)
Sectorsize: 512
Mode: r1w1e1
State: ACTIVE
Priority: 0
Flags: DIRTY
GenID: 0
SyncID: 1
ID: 3986018406
2. Name: ad2
Mediasize: 10262568448 (9.6G)
Sectorsize: 512
Mode: r1w1e1
State: SYNCHRONIZING
Priority: 0
Flags: DIRTY, SYNCHRONIZING
GenID: 0
SyncID: 1
Synchronized: 1%
ID: 1946262342
Обратите на SYNCHRONIZING в строке Flags. Для синхронизации дисков
потребуется некоторое время, в настоящее время синхронизировано 1%
данных. Приблизительно, время синхронизации составляет от 30 минут для
10Гб и 2.5 часа для 75Гб дисков. Если вам интересно, то вы можете
понаблюдать за процессом:
# gmirror status
Name Status Components
mirror/gm0 DEGRADED ad0
ad2 (2%)
Когда синхронизация закончится, вы увидите следующее сообщение:
GEOM_MIRROR: Device gm0: rebuilding provider ad2 finished.
GEOM_MIRROR: Device gm0: provider ad2 activated.
Если вы повторно выполните команду gmirror list, то увидите, что в
строке State значение DEGRADED изменилось на COMPLETE. Не волнуйтесь,
увидев в строке Flags состояние DIRTY, это означает, что система
сделала запись на диск, но еще не синхронизировала данные между
дисками, если потождать несколько секунд, не производя никаких
дисковых операций, то можно увидеть, как состояние изменится на NONE.
В финале действа, перезагрузите систему.
Во время загрузки вы должны будете увидеть следущие сообщения:
GEOM_MIRROR: Device gm0 created (id=2125638583).
GEOM_MIRROR: Device gm0: provider ad0 detected.
GEOM_MIRROR: Device gm0: provider ad2 detected.
GEOM_MIRROR: Device gm0: provider ad0 activated.
GEOM_MIRROR: Device gm0: provider ad2 activated.
GEOM_MIRROR: Device gm0: provider mirror/gm0 launched.
Mounting root from ufs:/dev/mirror/gm0s1a
Заключение
Утилиты GEOM находятся в постоянном развитии, разработчики вовсю
добавляют новые возможности и постоянно вносят изменения в страницы
руководства man.
Если вы желаете собрать статистику по производительности вашей
системы, то используйте gstat(8), так как хорошая скорость работы
через gmirror(8) необходима, особенно в случае неисправности одного из
дисков.
понедельник, 17 ноября 2008 г.
Change and Reset MySQL root Password
Other then the ways specified here to reset and change the root password for mySQL database in the case that the password is forgotten or lost, the following instructions explain in details the alternative way at the last part of the guide, where no additional file needs to be created:
- Login as root to the Windows or Unix-like (Unix, Linux or BSD) machine with the MySQL server.
- Stop the MySQL server by using either of the following command:
Linux: /etc/rc.d/init.d/mysql stop
FreeBSD: /usr/local/etc/rc.d/mysql-server.sh stop - Open the mysql server startup script (i.e. mysql-server.sh - the file executed to start or stop MySQL server.
- Add –skip-grant-tables to the end of the line that contains the mysqld_safe command as its parameter.
- Start MySQL server with the following command:
Linux: /etc/rc.d/init.d/mysql start
FreeBSD: /usr/local/etc/rc.d/mysql-server.sh start - Alternatively, start the MySQL server directly and skip the editing with the following command:
mysqld_safe –skip-grant-tables &
Depending on your path environment, you may need to point to the correct directory where mysqld_safe is instead.
- Run the following commands to login as the mysql user and connect to mysql user/permission database:
# mysql -u root mysql
- Run the update queries to change the MySQL password:
mysql> UPDATE user SET Password=PASSWORD(’newrootpassword’) WHERE User=’root’;
mysql> FLUSH PRIVILEGES;Note: Replace newrootpassword with the new root password for MySQL server. Flush Privileges is needed to making the password change effect immediately.
- Exit mysql database client by typing exit.
- Stop MySQL server with commands listed at step 2.
- Open the mysql server startup script edit in step 3 again and remove the –skip-grant-tables parameter that has been added.
- Start MySQL server by using command from step 5 or 6.
For Redhat Linux users, use the following instructions as the root user of Redhat Linux machine:
- Stop MySQL process by using command:
# killall mysqld
- Start the MySQL server with following options:
# /usr/libexec/mysqld -Sg –user=root &
- Start the MySQL client:
# mysql
You should see the following message:
Welcome to the MySQL monitor. Commands end with ; or g.
Your MySQL connection id is 1 to server version: 3.xx.xxType ‘help;’ or ‘h’ for help. Type ‘c’ to clear the buffer.
mysql>
- Use mysql database:
mysql> USE mysql
You should see the following message:
Reading table information for completion of table and column names
You can turn off this feature to get a quicker startup with -ADatabase changed
- Then, update the password for the root user with the following command:
UPDATE user SET password=password(”newpassword”) WHERE user=”root”;
Replace newpassword with your desired password. You should see the following message:
Query OK, 2 rows affected (0.03 sec)
Rows matched: 2 Changed: 2 Warnings: 0Rows affected may be different, but the Query OK should be there.
- Flush the database privileges to reload it in order to make the changes effective:
mysql> flush privileges;
You should get the following result:
Query OK, 0 rows affected (0.02 sec)
- Exit the MySQL client by typing exit.
- Kill the MySQL server process by typing killall mysqld.
- Then start MySQL again:
/etc/init.d/mysqld start
четверг, 3 июля 2008 г.
команды for *nix
Короткий список консольных команд, который облегчит вам жизнь в ОС Unix, Linux.
Информация о ядре и системе:
# uname -a # Версия ядра (BSD version)
# lsb_release -a # Полная версия о релизе (Full release info of any LSB distribution)
# cat /etc/SuSE-release # Узнать версию SuSE (Get SuSE version)
# cat /etc/debian_version # Узнать версию debian (Get Debian version)
Use /etc/DISTR-release with DISTR= lsb (Ubuntu), redhat, gentoo, mandrake, sun (Solaris), and so on.
# uptime # посмотреть время работы системы (Show how long the system has been running + load)
# hostname # посмотреть имя хоста (system’s host name)
# hostname -i # узнать IP хоста (Display the IP address of the host).
# man hier # описание файловой системы (Description of the file system hierarchy)
# last reboot # посмотреть историю перезагрузок (Show system reboot history)
Hardware Informations
Kernel detected hardware
# dmesg # Detected hardware and boot messages
# lsdev # Посмотреть информацию об установленном железе (information about installed hardware)
# dd if=/dev/mem bs=1k skip=768 count=256 2>/dev/null | strings -n 8 # Read BIOS
Linux
# cat /proc/cpuinfo # Модель процессора (CPU model)
# cat /proc/meminfo # Память (Hardware memory)
# grep MemTotal /proc/meminfo # Display the physical memory
# watch -n1 ‘cat /proc/interrupts’ # Watch changeable interrupts continuously
# free -m # Used and free memory (-m for MB)
# cat /proc/devices # Configured devices
# lspci -tv # Show PCI devices
# lsusb -tv # Show USB devices
# lshal # Show a list of all devices with their properties
# dmidecode # Show DMI/SMBIOS: hw info from the BIOS
FreeBSD
# sysctl hw.model # CPU model
# sysctl hw # Gives a lot of hardware information
# sysctl vm # Memory usage
# dmesg | grep “real mem” # Hardware memory
# sysctl -a | grep mem # Kernel memory settings and info
# sysctl dev # Configured devices
# pciconf -l -cv # Show PCI devices
# usbdevs -v # Show USB devices
# atacontrol list # Show ATA devices
Load, statistics and messages
The following commands are useful to find out what is going on on the system.
# top # display and update the top cpu processes
# mpstat 1 # display processors related statistics
# vmstat 2 # display virtual memory statistics
# iostat 2 # display I/O statistics (2 s intervals)
# systat -vmstat 1 # BSD summary of system statistics (1 s intervals)
# systat -tcp 1 # BSD tcp connections (try also -ip)
# systat -netstat 1 # BSD active network connections
# systat -ifstat 1 # BSD network traffic through active interfaces
# systat -iostat 1 # BSD CPU and and disk throughput
# tail -n 500 /var/log/messages # Last 500 kernel/syslog messages
# tail /var/log/warn # System warnings messages see syslog.conf
Users
# id # Show the active user id with login and group
# last # Show last logins on the system
# who # Show who is logged on the system
# groupadd admin # Add group “admin” and user colin (Linux/Solaris)
# useradd -c “Colin Barschel” -g admin -m colin
# userdel colin # Delete user colin (Linux/Solaris)
# adduser joe # FreeBSD add user joe (interactive)
# rmuser joe # FreeBSD delete user joe (interactive)
# pw groupadd admin # Use pw on FreeBSD
# pw groupmod admin -m newmember # Add a new member to a group
# pw useradd colin -c “Colin Barschel” -g admin -m -s /bin/tcsh
# pw userdel colin; pw groupdel admin
Encrypted passwords are stored in /etc/shadow for Linux and Solaris and /etc/master.passwd on FreeBSD. If the master.passwd is modified manually (say to delete a password), run # pwd_mkdb -p master.passwd to rebuild the database.
To temporarily prevent logins system wide (for all users but root) use nologin. The message in nologin will be displayed (might not work with ssh pre-shared keys).
# echo “Sorry no login now” > /etc/nologin # (Linux)
# echo “Sorry no login now” > /var/run/nologin # (FreeBSD)
Limits
Some application require higher limits on open files and sockets (like a proxy
web server, database). The default limits are usually too low.
Linux
Per shell/script
The shell limits are governed by ulimit. The status is checked
with ulimit -a. For example to change the open files limit from
1024 to 10240 do:
# ulimit -n 10240 # This is only valid within the shell
The ulimit command can be used in a script to change the limits for the script only.
Per user/process
Login users and applications can be configured in /etc/security/limits.conf. For example:
# cat /etc/security/limits.conf
* hard nproc 250 # Limit user processes
asterisk hard nofile 409600 # Limit application open files
System wide
Kernel limits are set with sysctl. Permanent limits are set in /etc/sysctl.conf.
# sysctl -a # View all system limits
# sysctl fs.file-max # View max open files limit
# sysctl fs.file-max=102400 # Change max open files limit
# echo “1024 50000″ > /proc/sys/net/ipv4/ip_local_port_range # port range
# cat /etc/sysctl.conf
fs.file-max=102400 # Permanent entry in sysctl.conf
# cat /proc/sys/fs/file-nr # How many file descriptors are in use
FreeBSD
Per shell/script
Use the command limits in csh or tcsh or as in Linux, use ulimit in an sh or bash shell.
Per user/process
The default limits on login are set in /etc/login.conf. An unlimited value is still limited by the system maximal value.
System wide
Kernel limits are also set with sysctl. Permanent limits are set in /etc/sysctl.conf or /boot/loader.conf. The syntax is the same as Linux but the keys are different.
# sysctl -a # View all system limits
# sysctl kern.maxfiles=XXXX # maximum number of file descriptors
kern.ipc.nmbclusters=32768 # Permanent entry in /etc/sysctl.conf
kern.maxfiles=65536 # Typical values for Squid
kern.maxfilesperproc=32768
kern.ipc.somaxconn=8192 # TCP queue. Better for apache/sendmail
# sysctl kern.openfiles # How many file descriptors are in use
# sysctl kern.ipc.numopensockets # How many open sockets are in use
# sysctl -w net.inet.ip.portrange.last=50000 # Default is 1024-5000
See The FreeBSD handbook Chapter 11http://www.freebsd.org/handbook/configtuning-kernel-limits.html for details.
Solaris
The following values in /etc/system will increase the maximum file descriptors per proc:
set rlim_fd_max = 4096 # Hard limit on file descriptors for a single proc
set rlim_fd_cur = 1024 # Soft limit on file descriptors for a single proc
Runlevels
Linux
Once booted, the kernel starts init which then starts rc which starts all scripts belonging to a runlevel. The scripts are stored in /etc/init.d and are linked into /etc/rc.d/rcN.d with N the runlevel number.
The default runlevel is configured in /etc/inittab. It is usually 3 or 5:
# grep default: /etc/inittab
id:3:initdefault:
The actual runlevel (the list is shown below) can be changed with init. For example to go from 3 to 5:
# init 5 # Enters runlevel 5
* 0 Shutdown and halt
* 1 Single-User mode (also S)
* 2 Multi-user without network
* 3 Multi-user with network
* 5 Multi-user with X
* 6 Reboot
Use chkconfig to configure the programs that will be started at boot in a runlevel.
# chkconfig –list # List all init scripts
# chkconfig –list sshd # Report the status of sshd
# chkconfig sshd –level 35 on # Configure sshd for levels 3 and 5
# chkconfig sshd off # Disable sshd for all runlevels
Debian and Debian based distributions like Ubuntu or Knoppix use the command update-rc.d to manage the runlevels scripts. Default is to start in 2,3,4 and 5 and shutdown in 0,1 and 6.
# update-rc.d sshd defaults # Activate sshd with the default runlevels
# update-rc.d sshd start 20 2 3 4 5 . stop 20 0 1 6 . # With explicit arguments
# update-rc.d -f sshd remove # Disable sshd for all runlevels
# shutdown -h now (or # poweroff) # Shutdown and halt the system
FreeBSD
The BSD boot approach is different from the SysV, there are no runlevels. The final boot state (single user, with or without X) is configured in /etc/ttys. All OS scripts are located in /etc/rc.d/ and in /usr/local/etc/rc.d/ for third-party applications. The activation of the service is configured in /etc/rc.conf and /etc/rc.conf.local. The default behavior is configured in /etc/defaults/rc.conf. The scripts responds at least to start|stop|status.
# /etc/rc.d/sshd status
sshd is running as pid 552.
# shutdown now # Go into single-user mode
# exit # Go back to multi-user mode
# shutdown -p now # Shutdown and halt the system
# shutdown -r now # Reboot
The process init can also be used to reach one of the following states level. For example # init 6 for reboot.
* 0 Halt and turn the power off (signal USR2)
* 1 Go to single-user mode (signal TERM)
* 6 Reboot the machine (signal INT)
* c Block further logins (signal TSTP)
* q Rescan the ttys(5) file (signal HUP)
Reset root password
Linux method 1
At the boot loader (lilo or grub), enter the following boot option:
init=/bin/sh
The kernel will mount the root partition and init will start the bourne shell
instead of rc and then a runlevel. Use the command passwd at the prompt to change the password and then reboot. Forget the single user mode as you need the password for that.
If, after booting, the root partition is mounted read only, remount it rw:
# mount -o remount,rw /
# passwd # or delete the root password (/etc/shadow)
# sync; mount -o remount,ro / # sync before to remount read only
# reboot
FreeBSD method 1
On FreeBSD, boot in single user mode, remount / rw and use passwd. You can select the single user mode on the boot menu (option 4) which is displayed for 10 seconds at startup. The single user mode will give you a root shell on the / partition.
# mount -u /; mount -a # will mount / rw
# passwd
# reboot
Unixes and FreeBSD and Linux method 2
Other Unixes might not let you go away with the simple init trick. The solution is to mount the root partition from an other OS (like a rescue CD) and change the password on the disk.
* Boot a live CD or installation CD into a rescue mode which will give you a shell.
* Find the root partition with fdisk e.g. fdisk /dev/sda
* Mount it and use chroot:
# mount -o rw /dev/ad4s3a /mnt
# chroot /mnt # chroot into /mnt
# passwd
# reboot
Kernel modules
Linux
# lsmod # List all modules loaded in the kernel
# modprobe isdn # To load a module (here isdn)
FreeBSD
# kldstat # List all modules loaded in the kernel
# kldload crypto # To load a module (here crypto)
Compile Kernel
Linux
# cd /usr/src/linux
# make mrproper # Clean everything, including config files
# make oldconfig # Reuse the old .config if existent
# make menuconfig # or xconfig (Qt) or gconfig (GTK)
# make # Create a compressed kernel image
# make modules # Compile the modules
# make modules_install # Install the modules
# make install # Install the kernel
# reboot
FreeBSD
To modify and rebuild the kernel, copy the generic configuration file to a new name and edit it as needed. It is however also possible to edit the file GENERIC directly.
# cd /usr/src/sys/i386/conf/
# cp GENERIC MYKERNEL
# cd /usr/src
# make buildkernel KERNCONF=MYKERNEL
# make installkernel KERNCONF=MYKERNEL
To rebuild the full OS:
# make buildworld # Build the full OS but not the kernel
# make buildkernel # Use KERNCONF as above if appropriate
# make installkernel
# reboot
# mergemaster -p # Compares only files known to be essential
# make installworld
# mergemaster # Update all configuration and other files
# reboot
For small changes in the source, sometimes the short version is enough:
# make kernel world # Compile/install all (for the brave only)
# mergemaster
# reboot
Processes
Listing | Priority | Background/Foreground | Top | Kill
Listing and PIDs
Each process has a unique number, the PID. A list of all running process is retrieved with ps.
# ps -auxefw # Extensive list of all running process
However more typical usage is with a pipe or with pgrep:
# ps axww | grep cron
586 ?? Is 0:01.48 /usr/sbin/cron -s
# ps aux | grep ’ss[h]‘ # Find all ssh pids without the grep pid
# pgrep -l sshd # Find the PIDs of processes by (part of) name
# echo $$ # The PID of your shell
# fuser -va 22/tcp # List processes using port 22 (Linux)
# fuser -va /home # List processes accessing the /home partiton
# strace df # Trace system calls and signals
# truss df # same as above on FreeBSD/Solaris/Unixware
# history | tail -50 # Display the last 50 used commands
Priority
Change the priority of a running process with renice. Negative numbers have a higher priority, the lowest is -20 and “nice” have a positive value.
# renice -5 586 # Stronger priority
586: old priority 0, new priority -5
Start the process with a defined priority with nice. Positive is “nice” or weak, negative is strong scheduling priority. Make sure you know if /usr/bin/nice or the shell built-in is used (check with # which nice).
# nice -n -5 top # Stronger priority (/usr/bin/nice)
# nice -n 5 top # Weaker priority (/usr/bin/nice)
# nice +5 top # tcsh builtin nice (same as above!)
While nice changes the CPU scheduler, an other useful command ionice will schedule the disk IO. This is very useful for intensive IO application which can bring a machine to its knees while still in a lower priority. The command is only available on Linux (AFAIK). You can select a class (idle - best effort - real time), the man page is short and well explained.
# ionice c3 -p123 # set idle class for pid 123
# ionice -c2 -n0 firefox # Run firefox with best effort and high priority
# ionice -c3 -p$$ # Set the actual shell to idle priority
For example last command is very useful to compile (or debug) a large project. Every command launched from this shell will have a lover priority and will not disturb the system. $$ is your shell pid (try echo $$).
Background/Foreground
When started from a shell, processes can be brought in the background and back to the foreground with [Ctrl]-[Z] (^Z), bg and fg. For example start two processes, bring them in the background, list the processes with jobs and bring one in the foreground.
# ping cb.vu > ping.log
^Z # ping is suspended (stopped) with [Ctrl]-[Z]
# bg # put in background and continues running
# jobs -l # List processes in background
[1] - 36232 Running ping cb.vu > ping.log
[2] + 36233 Suspended (tty output) top
# fg %2 # Bring process 2 back in foreground
Use nohup to start a process which has to keep running when the shell is closed (immune to hangups).
# nohup ping -i 60 > ping.log &
Top
The program top displays running information of processes. The program htop from htop.sourceforge.net is a very nice alternative and a more powerful version of top. Runs on Linux and FreeBSD (ports/sysutils/htop/).
# top
While top is running press the key h for a help overview. Useful keys are:
* u [user name] To display only the processes belonging to the user. Use + or blank to see all users
* k [pid] Kill the process with pid.
* 1 To display all processors statistics (Linux only)
* R Toggle normal/reverse sort.
Signals/Kill
Terminate or send a signal with kill or killall.
# ping -i 60 cb.vu > ping.log &
[1] 4712
# kill -s TERM 4712 # same as kill -15 4712
# killall -1 httpd # Kill HUP processes by exact name
# pkill -9 http # Kill TERM processes by (part of) name
# pkill -TERM -u www # Kill TERM processes owned by www
# fuser -k -TERM -m /home # Kill every process accessing /home (to umount)
Important signals are:
* 1 HUP (hang up)
* 2 INT (interrupt)
* 3 QUIT (quit)
* 9 KILL (non-catchable, non-ignorable kill)
* 15 TERM (software termination signal)
File System
Disk info | Boot | Disk usage | Opened files | Mount/remount | Mount SMB | Mount image | Burn ISO | Create image | Memory disk | Disk performance
Permissions
Change permission and ownership with chmod and chown. The default umask can be changed for all users in /etc/profile for Linux or /etc/login.conf for FreeBSD. The default umask is usually 022. The umask is subtracted from 777, thus umask 022 results in a permission 0f 755.
1 –x execute # Mode 764 = exec/read/write | read/write | read
2 -w- write # For: |– Owner –| |- Group-| |Oth|
4 r– read
ugo=a u=user, g=group, o=others, a=everyone
# chmod [OPTION] MODE[,MODE] FILE # MODE is of the form [ugoa]*([-+=]([rwxXst]))
# chmod 640 /var/log/maillog # Restrict the log -rw-r—–
# chmod u=rw,g=r,o= /var/log/maillog # Same as above
# chmod -R o-r /home/* # Recursive remove other readable for all users
# chmod u+s /path/to/prog # Set SUID bit on executable (know what you do!)
# find / -perm -u+s -print # Find all programs with the SUID bit
# chown user:group /path/to/file # Change the user and group ownership of a file
# chgrp group /path/to/file # Change the group ownership of a file
# chmod 640 `find ./ -type f -print` # Change permissions to 640 for all files
# chmod 751 `find ./ -type d -print` # Change permissions to 751 for all directories
Disk information
# diskinfo -v /dev/ad2 # information about disk (sector/size) FreeBSD
# hdparm -I /dev/sda # information about the IDE/ATA disk (Linux)
# fdisk /dev/ad2 # Display and manipulate the partition table
# smartctl -a /dev/ad2 # Display the disk SMART info
Boot
FreeBSD
To boot an old kernel if the new kernel doesn’t boot, stop the boot at during the count down.
# unload
# load kernel.old
# boot
System mount points/Disk usage
# mount | column -t # Show mounted file-systems on the system
# df # display free disk space and mounted devices
# cat /proc/partitions # Show all registered partitions (Linux)
Disk usage
# du -sh * # Directory sizes as listing
# du -csh # Total directory size of the current directory
# du -ks * | sort -n -r # Sort everything by size in kilobytes
# ls -lSr # Show files, biggest last
Who has which files opened
This is useful to find out which file is blocking a partition which has to be unmounted and gives a typical error of:
# umount /home/
umount: unmount of /home # umount impossible because a file is locking home
failed: Device busy
FreeBSD and most Unixes
# fstat -f /home # for a mount point
# fstat -p PID # for an application with PID
# fstat -u user # for a user name
Find opened log file (or other opened files), say for Xorg:
# ps ax | grep Xorg | awk ‘{print $1}’
1252
# fstat -p 1252
USER CMD PID FD MOUNT INUM MODE SZ|DV R/W
root Xorg 1252 root / 2 drwxr-xr-x 512 r
root Xorg 1252 text /usr 216016 -rws–x–x 1679848 r
root Xorg 1252 0 /var 212042 -rw-r–r– 56987 w
The file with inum 212042 is the only file in /var:
# find -x /var -inum 212042
/var/log/Xorg.0.log
Linux
Find opened files on a mount point with fuser or lsof:
# fuser -m /home # List processes accessing /home
# lsof /home
COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME
tcsh 29029 eedcoba cwd DIR 0,18 12288 1048587 /home/eedcoba (guam:/home)
lsof 29140 eedcoba cwd DIR 0,18 12288 1048587 /home/eedcoba (guam:/home)
About an application:
ps ax | grep Xorg | awk ‘{print $1}’
3324
# lsof -p 3324
COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME
Xorg 3324 root 0w REG 8,6 56296 12492 /var/log/Xorg.0.log
About a single file:
# lsof /var/log/Xorg.0.log
COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME
Xorg 3324 root 0w REG 8,6 56296 12492 /var/log/Xorg.0.log
Mount/remount a file system
For example the cdrom. If listed in /etc/fstab:
# mount /cdrom
Or find the device in /dev/ or with dmesg
FreeBSD
# mount -v -t cd9660 /dev/cd0c /mnt # cdrom
# mount_cd9660 /dev/wcd0c /cdrom # other method
# mount -v -t msdos /dev/fd0c /mnt # floppy
Entry in /etc/fstab:
# Device Mountpoint FStype Options Dump Pass#
/dev/acd0 /cdrom cd9660 ro,noauto 0 0
To let users do it:
# sysctl vfs.usermount=1 # Or insert the line “vfs.usermount=1″ in /etc/sysctl.conf
Linux
# mount -t auto /dev/cdrom /mnt/cdrom # typical cdrom mount command
# mount /dev/hdc -t iso9660 -r /cdrom # typical IDE
# mount /dev/scd0 -t iso9660 -r /cdrom # typical SCSI cdrom
# mount /dev/sdc0 -t ntfs-3g /windows # typical SCSI
Entry in /etc/fstab:
/dev/cdrom /media/cdrom subfs noauto,fs=cdfss,ro,procuid,nosuid,nodev,exec 0 0
Mount a FreeBSD partition with Linux
Find the partition number containing with fdisk, this is usually the root partition, but it could be an other BSD slice too. If the FreeBSD has many slices, they are the one not listed in the fdisk table, but visible in /dev/sda* or /dev/hda*.
# fdisk /dev/sda # Find the FreeBSD partition
/dev/sda3 * 5357 7905 20474842+ a5 FreeBSD
# mount -t ufs -o ufstype=ufs2,ro /dev/sda3 /mnt
/dev/sda10 = /tmp; /dev/sda11 /usr # The other slices
Remount
Remount a device without unmounting it. Necessary for fsck for example
# mount -o remount,ro / # Linux
# mount -o ro / # FreeBSD
Copy the raw data from a cdrom into an iso image:
# dd if=/dev/cd0c of=file.iso
Add swap on-the-fly
Suppose you need more swap (right now), say a 2GB file /swap2gb (Linux only).
# dd if=/dev/zero of=/swap2gb bs=1024k count=2000
# mkswap /swap2gb # create the swap area
# swapon /swap2gb # activate the swap. It now in use
# swapoff /swap2gb # when done deactivate the swap
# rm /swap2gb
Mount an SMB share
Suppose we want to access the SMB share myshare on the computer smbserver, the address as typed on a Windows PC is \\smbserver\myshare\. We mount on /mnt/smbshare. Warning> cifs wants an IP or DNS name, not a Windows name.
Linux
# smbclient -U user -I 192.168.16.229 -L //smbshare/ # List the shares
# mount -t smbfs -o username=winuser //smbserver/myshare /mnt/smbshare
# mount -t cifs -o username=winuser,password=winpwd //192.168.16.229/myshare /mnt/share
Additionally with the package mount.cifs it is possible to store the credentials in a file, for example /home/user/.smb:
username=winuser
password=winpwd
And mount as follow:
# mount -t cifs -o credentials=/home/user/.smb //192.168.16.229/myshare /mnt/smbshare
FreeBSD
Use -I to give the IP (or DNS name); smbserver is the Windows name.
# smbutil view -I 192.168.16.229 //winuser@smbserver # List the shares
# mount_smbfs -I 192.168.16.229 //winuser@smbserver/myshare /mnt/smbshare
Mount an image
Linux loop-back
# mount -t iso9660 -o loop file.iso /mnt # Mount a CD image
# mount -t ext3 -o loop file.img /mnt # Mount an image with ext3 fs
FreeBSD
With memory device (do # kldload md.ko if necessary):
# mdconfig -a -t vnode -f file.iso -u 0
# mount -t cd9660 /dev/md0 /mnt
# umount /mnt; mdconfig -d -u 0 # Cleanup the md device
Or with virtual node:
# vnconfig /dev/vn0c file.iso; mount -t cd9660 /dev/vn0c /mnt
# umount /mnt; vnconfig -u /dev/vn0c # Cleanup the vn device
Solaris and FreeBSD
with loop-back file interface or lofi:
# lofiadm -a file.iso
# mount -F hsfs -o ro /dev/lofi/1 /mnt
# umount /mnt; lofiadm -d /dev/lofi/1 # Cleanup the lofi device
Create and burn an ISO image
This will copy the cd or DVD sector for sector. Without conv=notrunc, the image will be smaller if there is less content on the cd. See below and the dd examples.
# dd if=/dev/hdc of=/tmp/mycd.iso bs=2048 conv=notrunc
Use mkisofs to create a CD/DVD image from files in a directory. To overcome the file names restrictions: -r enables the Rock Ridge extensions common to UNIX systems, -J enables Joliet extensions used by Microsoft systems. -L allows ISO9660 filenames to begin with a period.
# mkisofs -J -L -r -V TITLE -o imagefile.iso /path/to/dir
On FreeBSD, mkisofs is found in the ports in sysutils/cdrtools.
Burn a CD/DVD ISO image
FreeBSD
FreeBSD does not enable DMA on ATAPI drives by default. DMA is enabled with the sysctl command and the arguments below, or with /boot/loader.conf with the following entries:
hw.ata.ata_dma=”1″
hw.ata.atapi_dma=”1″
Use burncd with an ATAPI device (burncd is part of the base system) and cdrecord (in sysutils/cdrtools) with a SCSI drive.
# burncd -f /dev/acd0 data imagefile.iso fixate # For ATAPI drive
# cdrecord -scanbus # To find the burner device (like 1,0,0)
# cdrecord dev=1,0,0 imagefile.iso
Linux
Also use cdrecord with Linux as described above. Additionally it is possible to use the native ATAPI interface which is found with:
# cdrecord dev=ATAPI -scanbus
And burn the CD/DVD as above.
dvd+rw-tools
The dvd+rw-tools package (FreeBSD: ports/sysutils/dvd+rw-tools) can do it all and includes growisofs to burn CDs or DVDs. The examples refere to the dvd device as /dev/dvd which could be a symlink to /dev/scd0 (typical scsi on Linux) or /dev/cd0 (typical FreeBSD) or /dev/rcd0c (typical NetBSD/OpenBSD character SCSI) or /dev/rdsk/c0t1d0s2 (Solaris example of a character SCSI/ATAPI CD-ROM device). There is a nice documentation with examples on the FreeBSD handbook chapter 18.7http://www.freebsd.org/handbook/creating-dvds.html.
# -dvd-compat closes the disk
# growisofs -dvd-compat -Z /dev/dvd=imagefile.iso # Burn existing iso image
# growisofs -dvd-compat -Z /dev/dvd -J -R /p/to/data # Burn directly
Convert a Nero .nrg file to .iso
Nero simply adds a 300Kb header to a normal iso image. This can be trimmed with dd.
# dd bs=1k if=imagefile.nrg of=imagefile.iso skip=300
Convert a bin/cue image to .iso
The little bchunk programhttp://freshmeat.net/projects/bchunk/ can do this. It is in the FreeBSD ports in sysutils/bchunk.
# bchunk imagefile.bin imagefile.cue imagefile.iso
Create a file based image
For example a partition of 1GB using the file /usr/vdisk.img. Here we use the vnode 0, but it could also be 1.
FreeBSD
# dd if=/dev/random of=/usr/vdisk.img bs=1K count=1M
# mdconfig -a -t vnode -f /usr/vdisk.img -u 0 # Creates device /dev/md1
# bsdlabel -w /dev/md0
# newfs /dev/md0c
# mount /dev/md0c /mnt
# umount /mnt; mdconfig -d -u 0; rm /usr/vdisk.img # Cleanup the md device
The file based image can be automatically mounted during boot with an entry in /etc/rc.conf and /etc/fstab. Test your setup with # /etc/rc.d/mdconfig start (first delete the md0 device with # mdconfig -d -u 0).
Note however that this automatic setup will only work if the file image is NOT on the root partition. The reason is that the /etc/rc.d/mdconfig script is executed very early buring boot and the root partition is still read-only. Images located outside the root partition will be mounted later with the script /etc/rc.d/mdconfig2.
/boot/loader.conf:
md_load=”YES”
/etc/rc.conf:
# mdconfig_md0=”-t vnode -f /usr/vdisk.img” # /usr is not on the root partition
/etc/fstab: (The 0 0 at the end is important, it tell fsck to ignore this device, as is does not exist yet)
/dev/md0 /usr/vdisk ufs rw 0 0
It is also possible to increase the size of the image afterward, say for example 300 MB larger.
# umount /mnt; mdconfig -d -u 0
# dd if=/dev/zero bs=1m count=300 >> /usr/vdisk.img
# mdconfig -a -t vnode -f /usr/vdisk.img -u 0
# growfs /dev/md0
# mount /dev/md0c /mnt # File partition is now 300 MB larger
Linux
# dd if=/dev/zero of=/usr/vdisk.img bs=1024k count=1024
# mkfs.ext3 /usr/vdisk.img
# mount -o loop /usr/vdisk.img /mnt
# umount /mnt; rm /usr/vdisk.img # Cleanup
Linux with losetup
/dev/zero is much faster than urandom, but less secure for encryption.
# dd if=/dev/urandom of=/usr/vdisk.img bs=1024k count=1024
# losetup /dev/loop0 /usr/vdisk.img # Creates and associates /dev/loop0
# mkfs.ext3 /dev/loop0
# mount /dev/loop0 /mnt
# losetup -a # Check used loops
# umount /mnt
# losetup -d /dev/loop0 # Detach
# rm /usr/vdisk.img
Create a memory file system
A memory based file system is very fast for heavy IO application. How to create a 64 MB partition mounted on /memdisk:
FreeBSD
# mount_mfs -o rw -s 64M md /memdisk
# umount /memdisk; mdconfig -d -u 0 # Cleanup the md device
md /memdisk mfs rw,-s64M 0 0 # /etc/fstab entry
Linux
# mount -t tmpfs -osize=64m tmpfs /memdisk
Disk performance
Read and write a 1 GB file on partition ad4s3c (/home)
# time dd if=/dev/ad4s3c of=/dev/null bs=1024k count=1000
# time dd if=/dev/zero bs=1024k count=1000 of=/home/1Gb.file
# hdparm -tT /dev/hda # Linux only
Network
Routing | Additional IP | Change MAC | Ports | Firewall | IP Forward | NAT | DNS | DHCP | Traffic | QoS | NIS
Debugging (See also Traffic analysis)
Linux
# ethtool eth0 # Show the ethernet status (replaces mii-diag)
# ethtool -s eth0 speed 100 duplex full # Force 100Mbit Full duplex
# ethtool -s eth0 autoneg off # Disable auto negotiation
# ethtool -p eth1 # Blink the ethernet led - very useful when supported
# ip link show # Display all interfaces on Linux (similar to ifconfig)
# ip link set eth0 up # Bring device up (or down). Same as “ifconfig eth0 up”
# ip addr show # Display all IP addresses on Linux (similar to ifconfig)
# ip neigh show # Similar to arp -a
Other OSes
# ifconfig fxp0 # Check the “media” field on FreeBSD
# arp -a # Check the router (or host) ARP entry (all OS)
# ping cb.vu # The first thing to try…
# traceroute cb.vu # Print the route path to destination
# ifconfig fxp0 media 100baseTX mediaopt full-duplex # 100Mbit full duplex (FreeBSD)
# netstat -s # System-wide statistics for each network protocol
Additional commands which are not always installed per default but easy to find:
# arping 192.168.16.254 # Ping on ethernet layer
# tcptraceroute -f 5 cb.vu # uses tcp instead of icmp to trace throught firewalls
Routing
Print routing table
# route -n # Linux or use “ip route”
# netstat -rn # Linux, BSD and UNIX
# route print # Windows
Add and delete a route
FreeBSD
# route add 212.117.0.0/16 192.168.1.1
# route delete 212.117.0.0/16
# route add default 192.168.1.1
Add the route permanently in /etc/rc.conf
static_routes=”myroute”
route_myroute=”-net 212.117.0.0/16 192.168.1.1″
Linux
# route add -net 192.168.20.0 netmask 255.255.255.0 gw 192.168.16.254
# ip route add 192.168.20.0/24 via 192.168.16.254 # same as above with ip route
# route add -net 192.168.20.0 netmask 255.255.255.0 dev eth0
# route add default gw 192.168.51.254
# ip route add default via 192.168.51.254 dev eth0 # same as above with ip route
# route delete -net 192.168.20.0 netmask 255.255.255.0
Solaris
# route add -net 192.168.20.0 -netmask 255.255.255.0 192.168.16.254
# route add default 192.168.51.254 1 # 1 = hops to the next gateway
# route change default 192.168.50.254 1
Permanent entries are set in entry in /etc/defaultrouter.
Windows
# Route add 192.168.50.0 mask 255.255.255.0 192.168.51.253
# Route add 0.0.0.0 mask 0.0.0.0 192.168.51.254
Use add -p to make the route persistent.
Configure additional IP addresses
Linux
# ifconfig eth0 192.168.50.254 netmask 255.255.255.0 # First IP
# ifconfig eth0:0 192.168.51.254 netmask 255.255.255.0 # Second IP
# ip addr add 192.168.50.254/24 dev eth0 # Equivalent ip commands
# ip addr add 192.168.51.254/24 dev eth0 label eth0:1
FreeBSD
# ifconfig fxp0 inet 192.168.50.254/24 # First IP
# ifconfig fxp0 alias 192.168.51.254 netmask 255.255.255.0 # Second IP
Permanent entries in /etc/rc.conf
ifconfig_fxp0=”inet 192.168.50.254 netmask 255.255.255.0″
ifconfig_fxp0_alias0=”192.168.51.254 netmask 255.255.255.0″
Solaris
Check the settings with ifconfig -a
# ifconfig hme0 plumb # Enable the network card
# ifconfig hme0 192.168.50.254 netmask 255.255.255.0 up # First IP
# ifconfig hme0:1 192.168.51.254 netmask 255.255.255.0 up # Second IP
Change MAC address
Normally you have to bring the interface down before the change. Don’t tell me why you want to change the MAC address…
# ifconfig eth0 down
# ifconfig eth0 hw ether 00:01:02:03:04:05 # Linux
# ifconfig fxp0 link 00:01:02:03:04:05 # FreeBSD
# ifconfig hme0 ether 00:01:02:03:04:05 # Solaris
# sudo ifconfig en0 ether 00:01:02:03:04:05 # Mac OS X Tiger
# sudo ifconfig en0 lladdr 00:01:02:03:04:05 # Mac OS X Leopard
Many tools exist for Windows. For example etherchangehttp://ntsecurity.nu/toolbox/etherchange. Or look for “Mac Makeup”, “smac”.
Ports in use
Listening open ports:
# netstat -an | grep LISTEN
# lsof -i # Linux list all Internet connections
# socklist # Linux display list of open sockets
# sockstat -4 # FreeBSD application listing
# netstat -anp –udp –tcp | grep LISTEN # Linux
# netstat -tup # List active connections to/from system (Linux)
# netstat -tupl # List listening ports from system (Linux)
# netstat -ano # Windows
Firewall
Check if a firewall is running (typical configuration only):
Linux
# iptables -L -n -v # For status
Open the iptables firewall
# iptables -P INPUT ACCEPT # Open everything
# iptables -P FORWARD ACCEPT
# iptables -P OUTPUT ACCEPT
# iptables -Z # Zero the packet and byte counters in all chains
# iptables -F # Flush all chains
# iptables -X # Delete all chains
FreeBSD
# ipfw show # For status
# ipfw list 65535 # if answer is “65535 deny ip from any to any” the fw is disabled
# sysctl net.inet.ip.fw.enable=0 # Disable
# sysctl net.inet.ip.fw.enable=1 # Enable
IP Forward for routing
Linux
Check and then enable IP forward with:
# cat /proc/sys/net/ipv4/ip_forward # Check IP forward 0=off, 1=on
# echo 1 > /proc/sys/net/ipv4/ip_forward
or edit /etc/sysctl.conf with:
net.ipv4.ip_forward = 1
FreeBSD
Check and enable with:
# sysctl net.inet.ip.forwarding # Check IP forward 0=off, 1=on
# sysctl net.inet.ip.forwarding=1
# sysctl net.inet.ip.fastforwarding=1 # For dedicated router or firewall
Permanent with entry in /etc/rc.conf:
gateway_enable=”YES” # Set to YES if this host will be a gateway.
Solaris
# ndd -set /dev/ip ip_forwarding 1 # Set IP forward 0=off, 1=on
NAT Network Address Translation
Linux
# iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE # to activate NAT
# iptables -t nat -A PREROUTING -p tcp -d 78.31.70.238 –dport 20022 -j DNAT \
–to 192.168.16.44:22 # Port forward 20022 to internal IP port ssh
# iptables -t nat -A PREROUTING -p tcp -d 78.31.70.238 –dport 993:995 -j DNAT \
–to 192.168.16.254:993:995 # Port forward of range 993-995
# ip route flush cache
# iptables -L -t nat # Check NAT status
Delete the port forward with -D instead of -A.
FreeBSD
# natd -s -m -u -dynamic -f /etc/natd.conf -n fxp0
Or edit /etc/rc.conf with:
firewall_enable=”YES” # Set to YES to enable firewall functionality
firewall_type=”open” # Firewall type (see /etc/rc.firewall)
natd_enable=”YES” # Enable natd (if firewall_enable == YES).
natd_interface=”tun0″ # Public interface or IP address to use.
natd_flags=”-s -m -u -dynamic -f /etc/natd.conf”
Port forward with:
# cat /etc/natd.conf
same_ports yes
use_sockets yes
unregistered_only
# redirect_port tcp insideIP:2300-2399 3300-3399 # port range
redirect_port udp 192.168.51.103:7777 7777
DNS
On Unix the DNS entries are valid for all interfaces and are stored in /etc/resolv.conf. The domain to which the host belongs is also stored in this file. A minimal configuration is:
nameserver 78.31.70.238
search sleepyowl.net intern.lab
domain sleepyowl.net
Check the system domain name with:
# hostname -d # Same as dnsdomainname
Windows
On Windows the DNS are configured per interface. To display the configured DNS and to flush the DNS cache use:
# ipconfig /? # Display help
# ipconfig /all # See all information including DNS
# ipconfig /flushdns # Flush the DNS cache
Forward queries
Dig is you friend to test the DNS settings. For example the public DNS server 213.133.105.2 ns.second-ns.de can be used for testing. See from which server the client receives the answer (simplified answer).
# dig sleepyowl.net
sleepyowl.net. 600 IN A 78.31.70.238
;; SERVER: 192.168.51.254#53(192.168.51.254)
The router 192.168.51.254 answered and the response is the A entry. Any entry can be queried and the DNS server can be selected with @:
# dig MX google.com
# dig @127.0.0.1 NS sun.com # To test the local server
# dig @204.97.212.10 NS MX heise.de # Query an external server
# dig AXFR @ns1.xname.org cb.vu # Get the full zone (zone transfer)
The program host is also powerful.
# host -t MX cb.vu # Get the mail MX entry
# host -t NS -T sun.com # Get the NS record over a TCP connection
# host -a sleepyowl.net # Get everything
Reverse queries
Find the name belonging to an IP address (in-addr.arpa.). This can be done with dig, host and nslookup:
# dig -x 78.31.70.238
# host 78.31.70.238
# nslookup 78.31.70.238
/etc/hosts
Single hosts can be configured in the file /etc/hosts instead of running named locally to resolve the hostname queries. The format is simple, for example:
78.31.70.238 sleepyowl.net sleepyowl
The priority between hosts and a dns query, that is the name resolution order, can be configured in /etc/nsswitch.conf AND /etc/host.conf. The file also exists on Windows, it is usually in:
C:\WINDOWS\SYSTEM32\DRIVERS\ETC
DHCP
Linux
Some distributions (SuSE) use dhcpcd as client. The default interface is eth0.
# dhcpcd -n eth0 # Trigger a renew (does not always work)
# dhcpcd -k eth0 # release and shutdown
The lease with the full information is stored in:
/var/lib/dhcpcd/dhcpcd-eth0.info
FreeBSD
FreeBSD (and Debian) uses dhclient. To configure an interface (for example bge0) run:
# dhclient bge0
The lease with the full information is stored in:
/var/db/dhclient.leases.bge0
Use
/etc/dhclient.conf
to prepend options or force different options:
# cat /etc/dhclient.conf
interface “rl0″ {
prepend domain-name-servers 127.0.0.1;
default domain-name “sleepyowl.net”;
supersede domain-name “sleepyowl.net”;
}
Windows
The dhcp lease can be renewed with ipconfig:
# ipconfig /renew # renew all adapters
# ipconfig /renew LAN # renew the adapter named “LAN”
# ipconfig /release WLAN # release the adapter named “WLAN”
Yes it is a good idea to rename you adapter with simple names!
Traffic analysis
Bmonhttp://people.suug.ch/~tgr/bmon/ is a small console bandwidth monitor and can display the flow on different interfaces.
Sniff with tcpdump
# tcpdump -nl -i bge0 not port ssh and src \(192.168.16.121 or 192.168.16.54\)
# tcpdump -l > dump && tail -f dump # Buffered output
# tcpdump -i rl0 -w traffic.rl0 # Write traffic in binary file
# tcpdump -r traffic.rl0 # Read from file (also for ethereal
# tcpdump port 80 # The two classic commands
# tcpdump host google.com
# tcpdump -i eth0 -X port \(110 or 143\) # Check if pop or imap is secure
# tcpdump -n -i eth0 icmp # Only catch pings
# tcpdump -i eth0 -s 0 -A port 80 | grep GET # -s 0 for full packet -A for ASCII
Additional important options:
* -A Print each packets in clear text (without header)
* -X Print packets in hex and ASCII
* -l Make stdout line buffered
* -D Print all interfaces available
On Windows use windump from www.winpcap.org. Use windump -D to list the interfaces.
Scan with nmap
Nmaphttp://insecure.org/nmap/ is a port scanner with OS detection, it is usually installed on most distributions and is also available for Windows. If you don’t scan your servers, hackers do it for you…
# nmap cb.vu # scans all reserved TCP ports on the host
# nmap -sP 192.168.16.0/24 # Find out which IP are used and by which host on 0/24
# nmap -sS -sV -O cb.vu # Do a stealth SYN scan with version and OS detection
PORT STATE SERVICE VERSION
22/tcp open ssh OpenSSH 3.8.1p1 FreeBSD-20060930 (protocol 2.0)
25/tcp open smtp Sendmail smtpd 8.13.6/8.13.6
80/tcp open http Apache httpd 2.0.59 ((FreeBSD) DAV/2 PHP/4.
[...]
Running: FreeBSD 5.X
Uptime 33.120 days (since Fri Aug 31 11:41:04 2007)
Other non standard but useful tools are hping (www.hping.org) an IP packet assembler/analyzer and fping (fping.sourceforge.net). fping can check multiple hosts in a round-robin fashion.
Traffic control (QoS)
Traffic control manages the queuing, policing, scheduling, and other traffic parameters for a network. The following examples are simple practical uses of the Linux and FreeBSD capabilities to better use the available bandwidth.
Limit upload
DSL or cable modems have a long queue to improve the upload throughput. However filling the queue with a fast device (e.g. ethernet) will dramatically decrease the interactivity. It is therefore useful to limit the device upload rate to match the physical capacity of the modem, this should greatly improve the interactivity. Set to about 90% of the modem maximal (cable) speed.
Linux
For a 512 Kbit upload modem.
# tc qdisc add dev eth0 root tbf rate 480kbit latency 50ms burst 1540
# tc -s qdisc ls dev eth0 # Status
# tc qdisc del dev eth0 root # Delete the queue
# tc qdisc change dev eth0 root tbf rate 220kbit latency 50ms burst 1540
FreeBSD
FreeBSD uses the dummynet traffic shaper which is configured with ipfw. Pipes are used to set limits the bandwidth in units of [K|M]{bit/s|Byte/s}, 0 means unlimited bandwidth. Using the same pipe number will reconfigure it. For example limit the upload bandwidth to 500 Kbit.
# kldload dummynet # load the module if necessary
# ipfw pipe 1 config bw 500Kbit/s # create a pipe with limited bandwidth
# ipfw add pipe 1 ip from me to any # divert the full upload into the pipe
Quality of service
Linux
Priority queuing with tc to optimize VoIP. See the full example on voip-info.org or www.howtoforge.com. Suppose VoIP uses udp on ports 10000:11024 and device eth0 (could also be ppp0 or so). The following commands define the QoS to three queues and force the VoIP traffic to queue 1 with QoS 0×1e (all bits set). The default traffic flows into queue 3 and QoS Minimize-Delay flows into queue 2.
# tc qdisc add dev eth0 root handle 1: prio priomap 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 0
# tc qdisc add dev eth0 parent 1:1 handle 10: sfq
# tc qdisc add dev eth0 parent 1:2 handle 20: sfq
# tc qdisc add dev eth0 parent 1:3 handle 30: sfq
# tc filter add dev eth0 protocol ip parent 1: prio 1 u32 \
match ip dport 10000 0×3C00 flowid 1:1 # use server port range
match ip dst 123.23.0.1 flowid 1:1 # or/and use server IP
Status and remove with
# tc -s qdisc ls dev eth0 # queue status
# tc qdisc del dev eth0 root # delete all QoS
Calculate port range and mask
The tc filter defines the port range with port and mask which you have to calculate. Find the 2^N ending of the port range, deduce the range and convert to HEX. This is your mask. Example for 10000 -> 11024, the range is 1024.
# 2^13 (8192) < 10000 < 2^14 (16384) # ending is 2^14 = 16384
# echo “obase=16;(2^14)-1024″ | bc # mask is 0×3C00
FreeBSD
The max link bandwidth is 500Kbit/s and we define 3 queues with priority 100:10:1 for VoIP:ssh:all the rest.
# ipfw pipe 1 config bw 500Kbit/s
# ipfw queue 1 config pipe 1 weight 100
# ipfw queue 2 config pipe 1 weight 10
# ipfw queue 3 config pipe 1 weight 1
# ipfw add 10 queue 1 proto udp dst-port 10000-11024
# ipfw add 11 queue 1 proto udp dst-ip 123.23.0.1 # or/and use server IP
# ipfw add 20 queue 2 dsp-port ssh
# ipfw add 30 queue 3 from me to any # all the rest
Status and remove with
# ipfw list # rules status
# ipfw pipe list # pipe status
# ipfw flush # deletes all rules but default
NIS Debugging
Some commands which should work on a well configured NIS client:
# ypwhich # get the connected NIS server name
# domainname # The NIS domain name as configured
# ypcat group # should display the group from the NIS server
# cd /var/yp && make # Rebuild the yp database
Is ypbind running?
# ps auxww | grep ypbind
/usr/sbin/ypbind -s -m -S servername1,servername2 # FreeBSD
/usr/sbin/ypbind # Linux
# yppoll passwd.byname
Map passwd.byname has order number 1190635041. Mon Sep 24 13:57:21 2007
The master server is servername.domain.net.
Linux
# cat /etc/yp.conf
ypserver servername
domain domain.net broadcast
SSH SCP
Public key | Fingerprint | SCP | Tunneling
Public key authentication
Connect to a host without password using public key authentication. The idea is to append your public key to the authorized_keys2 file on the remote host. For this example let’s connect host-client to host-server, the key is generated on the client.
* Use ssh-keygen to generate a key pair. ~/.ssh/id_dsa is the private key, ~/.ssh/id_dsa.pub is the public key.
* Copy only the public key to the server and append it to the file ~/.ssh/authorized_keys2 on your home on the server.
# ssh-keygen -t dsa -N ”
# cat ~/.ssh/id_dsa.pub | ssh you@host-server “cat - >> ~/.ssh/authorized_keys2″
Using the Windows client from ssh.com
The non commercial version of the ssh.com client can be downloaded the main ftp site: ftp.ssh.com/pub/ssh/. Keys generated by the ssh.com client need to be converted for the OpenSSH server. This can be done with the ssh-keygen command.
* Create a key pair with the ssh.com client: Settings - User Authentication - Generate New….
* I use Key type DSA; key length 2048.
* Copy the public key generated by the ssh.com client to the server into the ~/.ssh folder.
* The keys are in C:\Documents and Settings\%USERNAME%\Application Data\SSH\UserKeys.
* Use the ssh-keygen command on the server to convert the key:
# cd ~/.ssh
# ssh-keygen -i -f keyfilename.pub >> authorized_keys2
Notice: We used a DSA key, RSA is also possible. The key is not protected by a password.
Using putty for Windows
Puttyhttp://www.chiark.greenend.org.uk/~sgtatham/putty/download.html is a simple and free ssh client for Windows.
* Create a key pair with the puTTYgen program.
* Save the public and private keys (for example into C:\Documents and Settings\%USERNAME%\.ssh).
* Copy the public key to the server into the ~/.ssh folder:
# scp .ssh/puttykey.pub root@192.168.51.254:.ssh/
* Use the ssh-keygen command on the server to convert the key for OpenSSH:
# cd ~/.ssh
# ssh-keygen -i -f puttykey.pub >> authorized_keys2
* Point the private key location in the putty settings: Connection - SSH - Auth
Check fingerprint
At the first login, ssh will ask if the unknown host with the fingerprint has to be stored in the known hosts. To avoid a man-in-the-middle attack the administrator of the server can send you the server fingerprint which is then compared on the first login. Use ssh-keygen -l to get the fingerprint (on the server):
# ssh-keygen -l -f /etc/ssh/ssh_host_rsa_key.pub # For RSA key
2048 61:33:be:9b:ae:6c:36:31:fd:83:98:b7:99:2d:9f:cd /etc/ssh/ssh_host_rsa_key.pub
# ssh-keygen -l -f /etc/ssh/ssh_host_dsa_key.pub # For DSA key (default)
2048 14:4a:aa:d9:73:25:46:6d:0a:48:35:c7:f4:16:d4:ee /etc/ssh/ssh_host_dsa_key.pub
Now the client connecting to this server can verify that he is connecting to the right server:
# ssh linda
The authenticity of host ‘linda (192.168.16.54)’ can’t be established.
DSA key fingerprint is 14:4a:aa:d9:73:25:46:6d:0a:48:35:c7:f4:16:d4:ee.
Are you sure you want to continue connecting (yes/no)? yes
Secure file transfer
Some simple commands:
# scp file.txt host-two:/tmp
# scp joe@host-two:/www/*.html /www/tmp
# scp -r joe@host-two:/www /www/tmp
In Konqueror or Midnight Commander it is possible to access a remote file system with the address fish://user@gate. However the implementation is very slow.
Furthermore it is possible to mount a remote folder with sshfs a file system client based on SCP. See fuse sshfshttp://fuse.sourceforge.net/sshfs.html.
Tunneling
SSH tunneling allows to forward or reverse forward a port over the SSH connection, thus securing the traffic and accessing ports which would otherwise be blocked. This only works with TCP. The general nomenclature for forward and reverse is (see also ssh and NAT example):
# ssh -L localport:desthost:destport user@gate # desthost as seen from the gate
# ssh -R destport:desthost:localport user@gate # forwards your localport to destination
# ssh -X user@gate # To force X forwarding
This will connect to gate and forward the local port to the host desthost:destport. Note desthost is the destination host as seen by the gate, so if the connection is to the gate, then desthost is localhost. More than one port forward is possible.
Direct forward on the gate
Let say we want to access the CVS (port 2401) and http (port 80) which are running on the gate. This is the simplest example, desthost is thus localhost, and we use the port 8080 locally instead of 80 so we don’t need to be root. Once the ssh session is open, both services are accessible on the local ports.
# ssh -L 2401:localhost:2401 -L 8080:localhost:80 user@gate
Netbios and remote desktop forward to a second server
Let say a Windows smb server is behind the gate and is not running ssh. We need access to the smb share and also remote desktop to the server.
# ssh -L 139:smbserver:139 -L 3388:smbserver:3389 user@gate
The smb share can now be accessed with \\127.0.0.1\, but only if the local share is disabled, because the local share is listening on port 139.
It is possible to keep the local share enabled, for this we need to create a new virtual device with a new IP address for the tunnel, the smb share will be connected over this address. Furthermore the local RDP is already listening on 3389, so we choose 3388. For this example let’s use a virtual IP of 10.1.1.1.
* With putty use Source port=10.1.1.1:139. It is possible to create multiple loop devices and tunnel. On Windows 2000, only putty worked for me.
* With the ssh.com client, disable “Allow local connections only”. Since ssh.com will bind to all addresses, only a single share can be connected.
Now create the loopback interface with IP 10.1.1.1:
* # System->Control Panel->Add Hardware # Yes, Hardware is already connected
# Add a new hardware device (at bottom).
* # Install the hardware that I manually select # Network adapters # Microsoft , Microsoft Loopback Adapter.
* Configure the IP address of the fake device to 10.1.1.1 mask 255.255.255.0, no gateway.
* advanced->WINS, Enable LMHosts Lookup; Disable NetBIOS over TCP/IP.
* # Enable Client for Microsoft Networks. # Disable File and Printer Sharing for Microsoft Networks.
I HAD to reboot for this to work. Now connect to the smb share with \\10.1.1.1 and remote desktop to 10.1.1.1:3388.
Debug
If it is not working:
* Are the ports forwarded: netstat -an? Look at 0.0.0.0:139 or 10.1.1.1:139
* Does telnet 10.1.1.1 139 connect?
* You need the checkbox “Local ports accept connections from other hosts”.
* Is “File and Printer Sharing for Microsoft Networks” disabled on the loopback interface?
Connect two clients behind NAT
Suppose two clients are behind a NAT gateway and client cliadmin has to connect to client cliuser (the destination), both can login to the gate with ssh and are running Linux with sshd. You don’t need root access anywhere as long as the ports on gate are above 1024. We use 2022 on gate. Also since the gate is used locally, the option GatewayPorts is not necessary.
On client cliuser (from destination to gate):
# ssh -R 2022:localhost:22 user@gate # forwards client 22 to gate:2022
On client cliadmin (from host to gate):
# ssh -L 3022:localhost:2022 admin@gate # forwards client 3022 to gate:2022
Now the admin can connect directly to the client cliuser with:
# ssh -p 3022 admin@localhost # local:3022 -> gate:2022 -> client:22
Connect to VNC behind NAT
Suppose a Windows client with VNC listening on port 5900 has to be accessed from behind NAT.
On client cliwin to gate:
# ssh -R 15900:localhost:5900 user@gate
On client cliadmin (from host to gate):
# ssh -L 5900:localhost:15900 admin@gate
Now the admin can connect directly to the client VNC with:
# vncconnect -display :0 localhost
VPN with SSH
As of version 4.3, OpenSSH can use the tun/tap device to encrypt a tunnel. This is very similar to other TLS based VPN solutions like OpenVPN. One advantage with SSH is that there is no need to install and configure additional software. Additionally the tunnel uses the SSH authentication like pre shared keys. The drawback is that the encapsulation is done over TCP which might result in poor performance on a slow link. Also the tunnel is relying on a single (fragile) TCP connection. This technique is very useful for a quick IP based VPN setup. There is no limitation as with the single TCP port forward, all layer 3/4 protocols like ICMP, TCP/UDP, etc. are forwarded over the VPN. In any case, the following options are needed in the sshd_conf file:
PermitRootLogin yes
PermitTunnel yes
Single P2P connection
Here we are connecting two hosts, hclient and hserver with a peer to peer tunnel. The connection is started from hclient to hserver and is done as root. The tunnel end points are 10.0.1.1 (server) and 10.0.1.2 (client) and we create a device tun5 (this could also be an other number). The procedure is very simple:
* Connect with SSH using the tunnel option -w
* Configure the IP addresses of the tunnel. Once on the server and once on the client.
Connect to the server
Connection started on the client and commands are executed on the server.
Server is on Linux
cli># ssh -w5:5 root@hserver
srv># ifconfig tun5 10.0.1.1 netmask 255.255.255.252 # Executed on the server shell
Server is on FreeBSD
cli># ssh -w5:5 root@hserver
srv># ifconfig tun5 10.0.1.1 10.0.1.2 # Executed on the server shell
Configure the client
Commands executed on the client:
cli># ifconfig tun5 10.0.1.2 netmask 255.255.255.252 # Client is on Linux
cli># ifconfig tun5 10.0.1.2 10.0.1.1 # Client is on FreeBSD
The two hosts are now connected and can transparently communicate with any layer 3/4 protocol using the tunnel IP addresses.
Connect two networks
In addition to the p2p setup above, it is more useful to connect two private networks with an SSH VPN using two gates. Suppose for the example, netA is 192.168.51.0/24 and netB 192.168.16.0/24. The procedure is similar as above, we only need to add the routing. NAT must be activated on the private interface only if the gates are not the same as the default gateway of their network.
192.168.51.0/24 (netA)|gateA <-> gateB|192.168.16.0/24 (netB)
* Connect with SSH using the tunnel option -w.
* Configure the IP addresses of the tunnel. Once on the server and once on the client.
* Add the routing for the two networks.
* If necessary, activate NAT on the private interface of the gate.
The setup is started from gateA in netA.
Connect from gateA to gateB
Connection is started from gateA and commands are executed on gateB.
gateB is on Linux
gateA># ssh -w5:5 root@gateB
gateB># ifconfig tun5 10.0.1.1 netmask 255.255.255.252 # Executed on the gateB shell
gateB># route add -net 192.168.51.0 netmask 255.255.255.0 dev tun5
gateB># echo 1 > /proc/sys/net/ipv4/ip_forward # Only needed if not default gw
gateB># iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
gateB is on FreeBSD
gateA># ssh -w5:5 root@gateB # Creates the tun5 devices
gateB># ifconfig tun5 10.0.1.1 10.0.1.2 # Executed on the gateB shell
gateB># route add 192.168.51.0/24 10.0.1.2
gateB># sysctl net.inet.ip.forwarding=1 # Only needed if not default gw
gateB># natd -s -m -u -dynamic -n fxp0 # see NAT
gateA># sysctl net.inet.ip.fw.enable=1
Configure gateA
Commands executed on gateA:
gateA is on Linux
gateA># ifconfig tun5 10.0.1.2 netmask 255.255.255.252
gateA># route add -net 192.168.16.0 netmask 255.255.255.0 dev tun5
gateA># echo 1 > /proc/sys/net/ipv4/ip_forward
gateA># iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
gateA is on FreeBSD
gateA># ifconfig tun5 10.0.1.2 10.0.1.1
gateA># route add 192.168.16.0/24 10.0.1.2
gateA># sysctl net.inet.ip.forwarding=1
gateA># natd -s -m -u -dynamic -n fxp0 # see NAT
gateA># sysctl net.inet.ip.fw.enable=1
The two private networks are now transparently connected via the SSH VPN. The IP forward and NAT settings are only necessary if the gates are not the default gateways. In this case the clients would not know where to forward the response, and nat must be activated.
RSYNC
Rsync can almost completely replace cp and scp, furthermore interrupted transfers are efficiently restarted. A trailing slash (and the absence thereof) has different meanings, the man page is good… Here some examples:
Copy the directories with full content:
# rsync -a /home/colin/ /backup/colin/
# rsync -a /var/ /var_bak/
# rsync -aR –delete-during /home/user/ /backup/ # use relative (see below)
Same as before but over the network and with compression. Rsync uses SSH for the transport per default and will use the ssh key if they are set. Use “:” as with SCP. A typical remote copy:
# rsync -axSRzv /home/user/ user@server:/backup/user/
Exclude any directory tmp within /home/user/ and keep the relative folders hierarchy, that is the remote directory will have the structure /backup/home/user/. This is typically used for backups.
# rsync -azR –exclude /tmp/ /home/user/ user@server:/backup/
Use port 20022 for the ssh connection:
# rsync -az -e ’ssh -p 20022′ /home/colin/ user@server:/backup/colin/
Using the rsync daemon (used with “::”) is much faster, but not encrypted over ssh. The location of /backup is defined by the configuration in /etc/rsyncd.conf. The variable RSYNC_PASSWORD can be set to avoid the need to enter the password manually.
# rsync -axSRz /home/ ruser@hostname::rmodule/backup/
# rsync -axSRz ruser@hostname::rmodule/backup/ /home/ # To copy back
Some important options:
* -a, –archive archive mode; same as -rlptgoD (no -H)
* -r, –recursive recurse into directories
* -R, –relative use relative path names
* -H, –hard-links preserve hard links
* -S, –sparse handle sparse files efficiently
* -x, –one-file-system don’t cross file system boundaries
* –exclude=PATTERN exclude files matching PATTERN
* –delete-during receiver deletes during xfer, not before
* –delete-after receiver deletes after transfer, not before
Rsync on Windows
Rsync is available for Windows through cygwin or as stand-alone packaged in cwrsynchttp://sourceforge.net/projects/sereds. This is very convenient for automated backups. Install one of them (not both) and add the path to the Windows system variables: # Control Panel -> System -> tab Advanced, button Environment Variables. Edit the “Path” system variable and add the full path to the installed rsync, e.g. C:\Program Files\cwRsync\bin or C:\cygwin\bin. This way the commands rsync and ssh are available in a Windows command shell.
Public key authentication
Rsync is automatically tunneled over SSH and thus uses the SSH authentication on the server. Automatic backups have to avoid a user interaction, for this the SSH public key authentication can be used and the rsync command will run without a password.
All the following commands are executed within a Windows console. In a console (Start -> Run -> cmd) create and upload the key as described in SSH, change “user” and “server” as appropriate. If the file authorized_keys2 does not exist yet, simply copy id_dsa.pub to authorized_keys2 and upload it.
# ssh-keygen -t dsa -N ” # Creates a public and a private key
# rsync user@server:.ssh/authorized_keys2 . # Copy the file locally from the server
# cat id_dsa.pub >> authorized_keys2 # Or use an editor to add the key
# rsync authorized_keys2 user@server:.ssh/ # Copy the file back to the server
# del authorized_keys2 # Remove the local copy
Now test it with (in one line):
rsync -rv “/cygdrive/c/Documents and Settings/%USERNAME%/My Documents/” \
‘user@server:My\ Documents/’
Automatic backup
Use a batch file to automate the backup and add the file in the scheduled tasks (Programs -> Accessories -> System Tools -> Scheduled Tasks). For example create the file backup.bat and replace user@server.
@ECHO OFF
REM rsync the directory My Documents
SETLOCAL
SET CWRSYNCHOME=C:\PROGRAM FILES\CWRSYNC
SET CYGWIN=nontsec
SET CWOLDPATH=%PATH%
REM uncomment the next line when using cygwin
SET PATH=%CWRSYNCHOME%\BIN;%PATH%
echo Press Control-C to abort
rsync -av “/cygdrive/c/Documents and Settings/%USERNAME%/My Documents/” \
‘user@server:My\ Documents/’
pause
SUDO
Sudo is a standard way to give users some administrative rights without giving out the root password. Sudo is very useful in a multi user environment with a mix of server and workstations. Simply call the command with sudo:
# sudo /etc/init.d/dhcpd restart # Run the rc script as root
# sudo -u sysadmin whoami # Run cmd as an other user
Configuration
Sudo is configured in /etc/sudoers and must only be edited with visudo. The basic syntax is (the lists are comma separated):
user hosts = (runas) commands # In /etc/sudoers
* users one or more users or %group (like %wheel) to gain the rights
* hosts list of hosts (or ALL)
* runas list of users (or ALL) that the command rule can be run as. It is enclosed in ( )!
* commands list of commands (or ALL) that will be run as root or as (runas)
Additionally those keywords can be defined as alias, they are called User_Alias, Host_Alias, Runas_Alias and Cmnd_Alias. This is useful for larger setups. Here a sudoers example:
# cat /etc/sudoers
# Host aliases are subnets or hostnames.
Host_Alias DMZ = 212.118.81.40/28
Host_Alias DESKTOP = work1, work2
# User aliases are a list of users which can have the same rights
User_Alias ADMINS = colin, luca, admin
User_Alias DEVEL = joe, jack, julia
Runas_Alias DBA = oracle,pgsql
# Command aliases define the full path of a list of commands
Cmnd_Alias SYSTEM = /sbin/reboot,/usr/bin/kill,/sbin/halt,/sbin/shutdown,/etc/init.d/
Cmnd_Alias PW = /usr/bin/passwd [A-z]*, !/usr/bin/passwd root # Not root pwd!
Cmnd_Alias DEBUG = /usr/sbin/tcpdump,/usr/bin/wireshark,/usr/bin/nmap
# The actual rules
root,ADMINS ALL = (ALL) NOPASSWD: ALL # ADMINS can do anything w/o a password.
DEVEL DESKTOP = (ALL) NOPASSWD: ALL # Developers have full right on desktops
DEVEL DMZ = (ALL) NOPASSWD: DEBUG # Developers can debug the DMZ servers.
# User sysadmin can mess around in the DMZ servers with some commands.
sysadmin DMZ = (ALL) NOPASSWD: SYSTEM,PW,DEBUG
sysadmin ALL,!DMZ = (ALL) NOPASSWD: ALL # Can do anything outside the DMZ.
%dba ALL = (DBA) ALL # Group dba can run as database user.
# anyone can mount/unmount a cd-rom on the desktop machines
ALL DESKTOP = NOPASSWD: /sbin/mount /cdrom,/sbin/umount /cdrom
Encrypt Files
OpenSSL
A single file
Encrypt and decrypt:
# openssl des -salt -in file -out file.des
# openssl des -d -salt -in file.des -out file
Note that the file can of course be a tar archive.
tar and encrypt a whole directory
# tar -cf - directory | openssl des -salt -out directory.tar.des # Encrypt
# openssl des -d -salt -in directory.tar.des | tar -x # Decrypt
tar zip and encrypt a whole directory
# tar -zcf - directory | openssl des -salt -out directory.tar.gz.des # Encrypt
# openssl des -d -salt -in directory.tar.gz.des | tar -xz # Decrypt
* Use -k mysecretpassword after des to avoid the interactive password request. However note that this is highly insecure.
* Use des3 instead of des to get even stronger encryption (Triple-DES Cipher). This uses also more CPU.
GPG
GnuPG is well known to encrypt and sign emails or any data. Furthermore gpg and also provides an advanced key management system. This section only covers files encryption, not email usage, signing or the Web-Of-Trust.
The simplest encryption is with a symmetric cipher. In this case the file is encrypted with a password and anyone who knows the password can decrypt it, thus the keys are not needed. Gpg adds an extention “.gpg” to the encrypted file names.
# gpg -c file # Encrypt file with password
# gpg file.gpg # Decrypt file (optionally -o otherfile)
Using keys
For more details see GPG Quick Starthttp://www.madboa.com/geek/gpg-quickstart and GPG/PGP Basicshttp://aplawrence.com/Basics/gpg.html and the gnupg documentationhttp://gnupg.org/documentation among others.
The private and public keys are the heart of asymmetric cryptography. What is important to remember:
* Your public key is used by others to encrypt files that only you as the receiver can decrypt (not even the one who encrypted the file can decrypt it). The public key is thus meant to be distributed.
* Your private key is encrypted with your passphrase and is used to decrypt files which were encrypted with your public key. The private key must be kept secure. Also if the key or passphrase is lost, so are all the files encrypted with your public key.
* The key files are called keyrings as they can contain more than one key.
First generate a key pair. The defaults are fine, however you will have to enter at least your full name and email and optionally a comment. The comment is useful to create more than one key with the same name and email. Also you should use a “passphrase”, not a simple password.
# gpg –gen-key # This can take a long time
The keys are stored in ~/.gnupg/ on Unix, on Windows they are typically stored in
C:/Documents and Settings/%USERNAME%/Application Data/gnupg/.
~/.gnupg/pubring.gpg # Contains your public keys and all others imported
~/.gnupg/secring.gpg # Can contain more than one private key
Short reminder on most used options:
* -e encrypt data
* -d decrypt data
* -r NAME encrypt for recipient NAME (or ‘Full Name’ or ‘email@domain’)
* -a create ascii armored output of a key
* -o use as output file
The examples use ‘Your Name’ and ‘Alice’ as the keys are referred to by the email or full name or partial name. For example I can use ‘Colin’ or ‘c@cb.vu’ for my key [Colin Barschel (cb.vu)
Encrypt for personal use only
No need to export/import any key for this. You have both already.
# gpg -e -r ‘Your Name’ file # Encrypt with your public key
# gpg -o file -d file.gpg # Decrypt. Use -o or it goes to stdout
Encrypt - Decrypt with keys
First you need to export your public key for someone else to use it. And you need to import the public say from Alice to encrypt a file for her. You can either handle the keys in simple ascii files or use a public key server.
For example Alice export her public key and you import it, you can then encrypt a file for her. That is only Alice will be able to decrypt it.
# gpg -a -o alicekey.asc –export ‘Alice’ # Alice exported her key in ascii file.
# gpg –send-keys –keyserver subkeys.pgp.net KEYID # Alice put her key on a server.
# gpg –import alicekey.asc # You import her key into your pubring.
# gpg –search-keys –keyserver subkeys.pgp.net ‘Alice’ # or get her key from a server.
Once the keys are imported it is very easy to encrypt or decrypt a file:
# gpg -e -r ‘Alice’ file # Encrypt the file for Alice.
# gpg -d file.gpg -o file # Decrypt a file encrypted by Alice for you.
Key administration
# gpg –list-keys # list public keys and see the KEYIDS
The KEYID follows the ‘/’ e.g. for: pub 1024D/D12B77CE the KEYID is D12B77CE
# gpg –gen-revoke ‘Your Name’ # generate revocation certificate
# gpg –list-secret-keys # list private keys
# gpg –delete-keys NAME # delete a public key from local key ring
# gpg –delete-secret-key NAME # delete a secret key from local key ring
# gpg –fingerprint KEYID # Show the fingerprint of the key
# gpg –edit-key KEYID # Edit key (e.g sign or add/del email)
Encrypt Partitions
Linux with LUKS | Linux dm-crypt only | FreeBSD GELI | FBSD pwd only
There are (many) other alternative methods to encrypt disks, I only show here the methods I know and use. Keep in mind that the security is only good as long the OS has not been tempered with. An intruder could easily record the password from the keyboard events. Furthermore the data is freely accessible when the partition is attached and will not prevent an intruder to have access to it in this state.
Linux
Those instructions use the Linux dm-crypt (device-mapper) facility available on the 2.6 kernel. In this example, lets encrypt the partition /dev/sdc1, it could be however any other partition or disk, or USB or a file based partition created with losetup. In this case we would use /dev/loop0. See file image partition. The device mapper uses labels to identify a partition. We use sdc1 in this example, but it could be any string.
dm-crypt with LUKS
LUKS with dm-crypt has better encryption and makes it possible to have multiple passphrase for the same partition or to change the password easily. To test if LUKS is available, simply type # cryptsetup –help, if nothing about LUKS shows up, use the instructions below Without LUKS. First create a partition if necessary: fdisk /dev/sdc.
Create encrypted partition
# dd if=/dev/urandom of=/dev/sdc1 # Optional. For paranoids only (takes days)
# cryptsetup -y luksFormat /dev/sdc1 # This destroys any data on sdc1
# cryptsetup luksOpen /dev/sdc1 sdc1
# mkfs.ext3 /dev/mapper/sdc1 # create ext3 file system
# mount -t ext3 /dev/mapper/sdc1 /mnt
# umount /mnt
# cryptsetup luksClose sdc1 # Detach the encrypted partition
Attach
# cryptsetup luksOpen /dev/sdc1 sdc1
# mount -t ext3 /dev/mapper/sdc1 /mnt
Detach
# umount /mnt
# cryptsetup luksClose sdc1
dm-crypt without LUKS
# cryptsetup -y create sdc1 /dev/sdc1 # or any other partition like /dev/loop0
# dmsetup ls # check it, will display: sdc1 (254, 0)
# mkfs.ext3 /dev/mapper/sdc1 # This is done only the first time!
# mount -t ext3 /dev/mapper/sdc1 /mnt
# umount /mnt/
# cryptsetup remove sdc1 # Detach the encrypted partition
Do exactly the same (without the mkfs part!) to re-attach the partition. If the password is not correct, the mount command will fail. In this case simply remove the map sdc1 (cryptsetup remove sdc1) and create it again.
FreeBSD
The two popular FreeBSD disk encryption modules are gbde and geli. I now use geli because it is faster and also uses the crypto device for hardware acceleration. See The FreeBSD handbook Chapter 18.6http://www.freebsd.org/handbook/disks-encrypting.html for all the details. The geli module must be loaded or compiled into the kernel:
options GEOM_ELI
device crypto # or as module:
# echo ‘geom_eli_load=”YES”‘ >> /boot/loader.conf # or do: kldload geom_eli
Use password and key
I use those settings for a typical disk encryption, it uses a passphrase AND a key to encrypt the master key. That is you need both the password and the generated key /root/ad1.key to attach the partition. The master key is stored inside the partition and is not visible. See below for typical USB or file based image.
Create encrypted partition
# dd if=/dev/random of=/root/ad1.key bs=64 count=1 # this key encrypts the mater key
# geli init -s 4096 -K /root/ad1.key /dev/ad1 # -s 8192 is also OK for disks
# geli attach -k /root/ad1.key /dev/ad1 # DO make a backup of /root/ad1.key
# dd if=/dev/random of=/dev/ad1.eli bs=1m # Optional and takes a long time
# newfs /dev/ad1.eli # Create file system
# mount /dev/ad1.eli /mnt
Attach
# geli attach -k /root/ad1.key /dev/ad1
# fsck -ny -t ffs /dev/ad1.eli # In doubt check the file system
# mount /dev/ad1.eli /mnt
Detach
The detach procedure is done automatically on shutdown.
# umount /mnt
# geli detach /dev/ad1.eli
/etc/fstab
The encrypted partition can be configured to be mounted with /etc/fstab. The password will be prompted when booting. The following settings are required for this example:
# grep geli /etc/rc.conf
geli_devices=”ad1″
geli_ad1_flags=”-k /root/ad1.key”
# grep geli /etc/fstab
/dev/ad1.eli /home/private ufs rw 0 0
Use password only
It is more convenient to encrypt a USB stick or file based image with a passphrase only and no key. In this case it is not necessary to carry the additional key file around. The procedure is very much the same as above, simply without the key file. Let’s encrypt a file based image /cryptedfile of 1 GB.
# dd if=/dev/zero of=/cryptedfile bs=1M count=1000 # 1 GB file
# mdconfig -at vnode -f /cryptedfile
# geli init /dev/md0 # encrypts with password only
# geli attach /dev/md0
# newfs -U -m 0 /dev/md0.eli
# mount /dev/md0.eli /mnt
# umount /dev/md0.eli
# geli detach md0.eli
It is now possible to mount this image on an other system with the password only.
# mdconfig -at vnode -f /cryptedfile
# geli attach /dev/md0
# mount /dev/md0.eli /mnt
SSL Certificates
So called SSL/TLS certificates are cryptographic public key certificates and are composed of a public and a private key. The certificates are used to authenticate the endpoints and encrypt the data. They are used for example on a web server (https) or mail server (imaps).
Procedure
* We need a certificate authority to sign our certificate. This step is
usually provided by a vendor like Thawte, Verisign, etc., however we can also create our own.
* Create a certificate signing request. This request is like an unsigned certificate (the public part) and already contains all necessary information. The certificate request is normally sent to the authority vendor for signing. This step also creates the private key on the local machine.
* Sign the certificate with the certificate authority.
* If necessary join the certificate and the key in a single file to be used by the application (web server, mail server etc.).
Configure OpenSSL
We use /usr/local/certs as directory for this example check or edit /etc/ssl/openssl.cnf accordingly to your settings so you know where the files will be created. Here are the relevant part of openssl.cnf:
[ CA_default ]
dir = /usr/local/certs/CA # Where everything is kept
certs = $dir/certs # Where the issued certs are kept
crl_dir = $dir/crl # Where the issued crl are kept
database = $dir/index.txt # database index file.
Make sure the directories exist or create them
# mkdir -p /usr/local/certs/CA
# cd /usr/local/certs/CA
# mkdir certs crl newcerts private
# echo “01″ > serial # Only if serial does not exist
# touch index.txt
Create a certificate authority
If you do not have a certificate authority from a vendor, you’ll have to create your own. This step is not necessary if one intend to use a vendor to sign the request. To make a certificate authority (CA):
# openssl req -new -x509 -days 730 -config /etc/ssl/openssl.cnf \
-keyout CA/private/cakey.pem -out CA/cacert.pem
Create a certificate signing request
To make a new certificate (for mail server or web server for example), first create a request certificate with its private key. If your application do not support encrypted private key (for example UW-IMAP does not), then disable encryption with -nodes.
# openssl req -new -keyout newkey.pem -out newreq.pem \
-config /etc/ssl/openssl.cnf
# openssl req -nodes -new -keyout newkey.pem -out newreq.pem \
-config /etc/ssl/openssl.cnf # No encryption for the key
Sign the certificate
The certificate request has to be signed by the CA to be valid, this step is usually done by the vendor. Note: replace “servername” with the name of your server in the next commands.
# cat newreq.pem newkey.pem > new.pem
# openssl ca -policy policy_anything -out servernamecert.pem \
-config /etc/ssl/openssl.cnf -infiles new.pem
# mv newkey.pem servernamekey.pem
Now servernamekey.pem is the private key and servernamecert.pem is the server certificate.
Create united certificate
The IMAP server wants to have both private key and server certificate in the same file. And in general, this is also easier to handle, but the file has to be kept securely!. Apache also can deal with it well. Create a file servername.pem containing both the certificate and key.
* Open the private key (servernamekey.pem) with a text editor and copy the private key into the “servername.pem” file.
* Do the same with the server certificate (servernamecert.pem).
The final servername.pem file should look like this:
—–BEGIN RSA PRIVATE KEY—–
MIICXQIBAAKBgQDutWy+o/XZ/[...]qK5LqQgT3c9dU6fcR+WuSs6aejdEDDqBRQ
—–END RSA PRIVATE KEY—–
—–BEGIN CERTIFICATE—–
MIIERzCCA7CgAwIBAgIBBDANB[...]iG9w0BAQQFADCBxTELMAkGA1UEBhMCREUx
—–END CERTIFICATE—–
What we have now in the directory /usr/local/certs/:
* CA/private/cakey.pem (CA server private key)
* CA/cacert.pem (CA server public key)
* certs/servernamekey.pem (server private key)
* certs/servernamecert.pem (server signed certificate)
* certs/servername.pem (server certificate with private key)
Keep the private key secure!
View certificate information
To view the certificate information simply do:
# openssl x509 -text -in servernamecert.pem # View the certificate info
# openssl req -noout -text -in server.csr # View the request info
# openssl s_client -connect cb.vu:443 # Check a web server certificate
CVS
Server setup | CVS test | SSH tunneling | CVS usage
Server setup
Initiate the CVS
Decide where the main repository will rest and create a root cvs. For example /usr/local/cvs (as root):
# mkdir -p /usr/local/cvs
# setenv CVSROOT /usr/local/cvs # Set CVSROOT to the new location (local)
# cvs init # Creates all internal CVS config files
# cd /root
# cvs checkout CVSROOT # Checkout the config files to modify them
# cd CVSROOT
edit config ( fine as it is)
# cvs commit config
cat >> writers # Create a writers file (optionally also readers)
colin
^D # Use [Control][D] to quit the edit
# cvs add writers # Add the file writers into the repository
# cvs edit checkoutlist
# cat >> checkoutlist
writers
^D # Use [Control][D] to quit the edit
# cvs commit # Commit all the configuration changes
Add a readers file if you want to differentiate read and write permissions Note: Do not (ever) edit files directly into the main cvs, but rather checkout the file, modify it and check it in. We did this with the file writers to define the write access.
There are three popular ways to access the CVS at this point. The first two don’t need any further configuration. See the examples on CVSROOT below for how to use them:
* Direct local access to the file system. The user(s) need sufficient file permission to access the CS directly and there is no further authentication in addition to the OS login. However this is only useful if the repository is local.
* Remote access with ssh with the ext protocol. Any use with an ssh shell account and read/write permissions on the CVS server can access the CVS directly with ext over ssh without any additional tunnel. There is no server process running on the CVS for this to work. The ssh login does the authentication.
* Remote access with pserver. This is the preferred use for larger user base as the users are authenticated by the CVS pserver with a dedicated password database, there is therefore no need for local users accounts. This setup is explained below.
Network setup with inetd
The CVS can be run locally only if a network access is not needed. For a remote access, the daemon inetd can start the pserver with the following line in /etc/inetd.conf (/etc/xinetd.d/cvs on SuSE):
cvspserver stream tcp nowait cvs /usr/bin/cvs cvs \
–allow-root=/usr/local/cvs pserver
It is a good idea to block the cvs port from the Internet with the firewall and use an ssh tunnel to access the repository remotely.
Separate authentication
It is possible to have cvs users which are not part of the OS (no local users). This is actually probably wanted too from the security point of view. Simply add a file named passwd (in the CVSROOT directory) containing the users login and password in the crypt format. This is can be done with the apache htpasswd tool.
Note: This passwd file is the only file which has to be edited directly in the CVSROOT directory. Also it won’t be checked out. More info with htpasswd –help
# htpasswd -cb passwd user1 password1 # -c creates the file
# htpasswd -b passwd user2 password2
Now add :cvs at the end of each line to tell the cvs server to change the user to cvs (or whatever your cvs server is running under). It looks like this:
# cat passwd
user1:xsFjhU22u8Fuo:cvs
user2:vnefJOsnnvToM:cvs
Test it
Test the login as normal user (for example here me)
# cvs -d :pserver:colin@192.168.50.254:/usr/local/cvs login
Logging in to :pserver:colin@192.168.50.254:2401/usr/local/cvs
CVS password:
CVSROOT variable
This is an environment variable used to specify the location of the repository we’re doing operations on. For local use, it can be just set to the directory of the repository. For use over the network, the transport protocol must be specified. Set the CVSROOT variable with setenv CVSROOT string on a csh, tcsh shell, or with export CVSROOT=string on a sh, bash shell.
# setenv CVSROOT :pserver:
For example:
# setenv CVSROOT /usr/local/cvs # Used locally only
# setenv CVSROOT :local:/usr/local/cvs # Same as above
# setenv CVSROOT :ext:user@cvsserver:/usr/local/cvs # Direct access with SSH
# setenv CVS_RSH ssh # for the ext access
# setenv CVSROOT :pserver:user@cvsserver.254:/usr/local/cvs # network with pserver
When the login succeeded one can import a new project into the repository:
cd into your project root directory
cvs import
cvs -d :pserver:colin@192.168.50.254:/usr/local/cvs import MyProject MyCompany START
Where MyProject is the name of the new project in the repository (used later to checkout). Cvs will import the current directory content into the new project.
To checkout:
# cvs -d :pserver:colin@192.168.50.254:/usr/local/cvs checkout MyProject
or
# setenv CVSROOT :pserver:colin@192.168.50.254:/usr/local/cvs
# cvs checkout MyProject
SSH tunneling for CVS
We need 2 shells for this. On the first shell we connect to the cvs server with ssh and port-forward the cvs connection. On the second shell we use the cvs normally as if it where running locally.
on shell 1:
# ssh -L2401:localhost:2401 colin@cvs_server # Connect directly to the CVS server. Or:
# ssh -L2401:cvs_server:2401 colin@gateway # Use a gateway to reach the CVS
on shell 2:
# setenv CVSROOT :pserver:colin@localhost:/usr/local/cvs
# cvs login
Logging in to :pserver:colin@localhost:2401/usr/local/cvs
CVS password:
# cvs checkout MyProject/src
CVS commands and usage
Import
The import command is used to add a whole directory, it must be run from within the directory to be imported. Say the directory /devel/ contains all files and subdirectories to be imported. The directory name on the CVS (the module) will be called “myapp”.
# cvs import [options] directory-name vendor-tag release-tag
# cd /devel # Must be inside the project to import it
# cvs import myapp Company R1_0 # Release tag can be anything in one word
After a while a new directory “/devel/tools/” was added and it has to be imported too.
# cd /devel/tools
# cvs import myapp/tools Company R1_0
Checkout update add commit
# cvs co myapp/tools # Will only checkout the directory tools
# cvs co -r R1_1 myapp # Checkout myapp at release R1_1 (is sticky)
# cvs -q -d update -P # A typical CVS update
# cvs update -A # Reset any sticky tag (or date, option)
# cvs add newfile # Add a new file
# cvs add -kb newfile # Add a new binary file
# cvs commit file1 file2 # Commit the two files only
# cvs commit -m “message” # Commit all changes done with a message
Create a patch
It is best to create and apply a patch from the working development directory related to the project, or from within the source directory.
# cd /devel/project
# diff -Naur olddir newdir > patchfile # Create a patch from a directory or a file
# diff -Naur oldfile newfile > patchfile
Apply a patch
Sometimes it is necessary to strip a directory level from the patch, depending how it was created. In case of difficulties, simply look at the first lines of the patch and try -p0, -p1 or -p2.
# cd /devel/project
# patch –dry-run -p0 < patchfile # Test the path without applying it
# patch -p0 < patchfile
# patch -p1 <>
SVN
Server setup | SVN+SSH | SVN over http | SVN usage
Subversion (SVN)http://subversion.tigris.org/ is a version control system designed to be the successor of CVS (Concurrent Versions System). The concept is similar to CVS, but many shortcomings where improved. See also the SVN bookhttp://svnbook.red-bean.com/en/1.4/.
Server setup
The initiation of the repository is fairly simple (here for example /home/svn/ must exist):
# svnadmin create –fs-type fsfs /home/svn/project1
Now the access to the repository is made possible with:
* file:// Direct file system access with the svn client with. This requires local permissions on the file system.
* svn:// or svn+ssh:// Remote access with the svnserve server (also over SSH). This requires local permissions on the file system.
* http:// Remote access with webdav using apache. No local users are necessary for this method.
Using the local file system, it is now possible to import and then check out an existing project. Unlike with CVS it is not necessary to cd into the project directory, simply give the full path:
# svn import /project1/ file:///home/svn/project1/trunk -m ‘Initial import’
# svn checkout file:///home/svn/project1
The new directory “trunk” is only a convention, this is not required.
Remote access with ssh
No special setup is required to access the repository via ssh, simply replace file:// with svn+ssh/hostname. For example:
# svn checkout svn+ssh://hostname/home/svn/project1
As with the local file access, every user needs an ssh access to the server (with a local account) and also read/write access. This method might be suitable for a small group. All users could belong to a subversion group which owns the repository, for example:
# groupadd subversion
# groupmod -A user1 subversion
# chown -R root:subversion /home/svn
# chmod -R 770 /home/svn
Remote access with http (apache)
Remote access over http (https) is the only good solution for a larger user group. This method uses the apache authentication, not the local accounts. This is a typical but small apache configuration:
LoadModule dav_module modules/mod_dav.so
LoadModule dav_svn_module modules/mod_dav_svn.so
LoadModule authz_svn_module modules/mod_authz_svn.so # Only for access control
DAV svn
# any “/svn/foo” URL will map to a repository /home/svn/foo
SVNParentPath /home/svn
AuthType Basic
AuthName “Subversion repository”
AuthzSVNAccessFile /etc/apache2/svn.acl
AuthUserFile /etc/apache2/svn-passwd
Require valid-user
The apache server needs full access to the repository:
# chown -R www:www /home/svn
Create a user with htpasswd2:
# htpasswd -c /etc/svn-passwd user1 # -c creates the file
Access control svn.acl example
# Default it read access. “* =” would be default no access
[/]
* = r
[groups]
project1-developers = joe, jack, jane
# Give write access to the developers
[project1:]
@project1-developers = rw
SVN commands and usage
See also the Subversion Quick Reference Cardhttp://www.cs.put.poznan.pl/csobaniec/Papers/svn-refcard.pdf. Tortoise SVNhttp://tortoisesvn.tigris.org is a nice Windows interface.
Import
A new project, that is a directory with some files, is imported into the repository with the import command. Import is also used to add a directory with its content to an existing project.
# svn help import # Get help for any command
# Add a new directory (with content) into the src dir on project1
# svn import /project1/newdir http://host.url/svn/project1/trunk/src -m ‘add newdir’
Typical SVN commands
# svn co http://host.url/svn/project1/trunk # Checkout the most recent version
# Tags and branches are created by copying
# svn mkdir http://host.url/svn/project1/tags/ # Create the tags directory
# svn copy -m “Tag rc1 rel.” http://host.url/svn/project1/trunk \
http://host.url/svn/project1/tags/1.0rc1
# svn status [--verbose] # Check files status into working dir
# svn add src/file.h src/file.cpp # Add two files
# svn commit -m ‘Added new class file’ # Commit the changes with a message
# svn ls http://host.url/svn/project1/tags/ # List all tags
# svn move foo.c bar.c # Move (rename) files
# svn delete some_old_file # Delete files
Useful Commands
less | vi | mail | tar | dd | screen | find | Miscellaneous
less
The less command displays a text document on the console. It is present on most installation.
# less unixtoolbox.xhtml
Some important commands are (^N stands for [control]-[N]):
* h H good help on display
* f ^F ^V SPACE Forward one window (or N lines).
* b ^B ESC-v Backward one window (or N lines).
* F Forward forever; like “tail -f”.
* /pattern Search forward for (N-th) matching line.
* ?pattern Search backward for (N-th) matching line.
* n Repeat previous search (for N-th occurrence).
* N Repeat previous search in reverse direction.
* q quit
vi
Vi is present on ANY Linux/Unix installation (not gentoo?) and it is therefore useful to know some basic commands. There are two modes: command mode and insertion mode. The commands mode is accessed with [ESC], the insertion mode with i. Use : help if you are lost.
The editors nano and pico are usually available too and are easier (IMHO) to use.
Quit
* :w newfilename save the file to newfilename
* :wq or :x save and quit
* :q! quit without saving
Search and move
* /string Search forward for string
* ?string Search back for string
* n Search for next instance of string
* N Search for previous instance of string
* { Move a paragraph back
* } Move a paragraph forward
* 1G Move to the first line of the file
* nG Move to the n th line of the file
* G Move to the last line of the file
* :%s/OLD/NEW/g Search and replace every occurrence
Delete text
* dd delete current line
* D Delete to the end of the line
* dw Delete word
* x Delete character
* u Undo last
* U Undo all changes to current line
The mail command is a basic application to read and send email, it is usually installed. To send an email simply type “mail user@domain”. The first line is the subject, then the mail content. Terminate and send the email with a single dot (.) in a new line. Example:
# mail c@cb.vu
Subject: Your text is full of typos
“For a moment, nothing happened. Then, after a second or so,
nothing continued to happen.”
.
EOT
#
This is also working with a pipe:
# echo “This is the mail body” | mail c@cb.vu
This is also a simple way to test the mail server.
tar
The command tar (tape archive) creates and extracts archives of file and directories. The archive .tar is uncompressed, a compressed archive has the extension .tgz or .tar.gz (zip) or .tbz (bzip2). Do not use absolute path when creating an archive, you probably want to unpack it somewhere else. Some typical commands are:
Create
# cd /
# tar -cf home.tar home/ # archive the whole /home directory (c for create)
# tar -czf home.tgz home/ # same with zip compression
# tar -cjf home.tbz home/ # same with bzip2 compression
Only include one (or two) directories from a tree, but keep the relative structure. For example archive /usr/local/etc and /usr/local/www and the first directory in the archive should be local/.
# tar -C /usr -czf local.tgz local/etc local/www
# tar -C /usr -xzf local.tgz # To untar the local dir into /usr
# cd /usr; tar -xzf local.tgz # Is the same as above
Extract
# tar -tzf home.tgz # look inside the archive without extracting (list)
# tar -xf home.tar # extract the archive here (x for extract)
# tar -xzf home.tgz # same with zip compression
# tar -xjf home.tgz # same with bzip2 compression
# tar -xjf home.tgz home/colin/file.txt # Restore a single file
More advanced
# tar c dir/ | gzip | ssh user@remote ‘dd of=dir.tgz’ # arch dir/ and store remotely.
# tar cvf - `find . -print` > backup.tar # arch the current directory.
# tar -cf - -C /etc . | tar xpf - -C /backup/etc # Copy directories
# tar -cf - -C /etc . | ssh user@remote tar xpf - -C /backup/etc # Remote copy.
# tar -czf home.tgz –exclude ‘*.o’ –exclude ‘tmp/’ home/
dd
The program dd (disk dump or destroy disk or see the meaning of dd) is used to copy partitions and disks and for other copy tricks. Typical usage:
# dd if=
Important conv options:
* notrunc do not truncate the output file, all zeros will be written as zeros.
* noerror continue after read errors (e.g. bad blocks)
* sync pad every input block with Nulls to ibs-size
The default byte size is 512 (one block). The MBR, where the partiton table is located, is on the first block, the first 63 blocks of a disk are empty. Larger byte sizes are faster to copy but require also more memory.
Backup and restore
# dd if=/dev/hda of=/dev/hdc bs=16065b # Copy disk to disk (same size)
# dd if=/dev/sda7 of /home/root.img bs=4096 conv=notrunc,noerror # Backup /
# dd if /home/root.img of=/dev/sda7 bs=4096 conv=notrunc,noerror # Restore /
# dd bs=1M if=/dev/ad4s3e | gzip -c > ad4s3e.gz # Zip the backup
# gunzip -dc ad4s3e.gz | dd of=/dev/ad0s3e bs=1M # Restore the zip
# dd bs=1M if=/dev/ad4s3e | gzip | ssh eedcoba@fry ‘dd of=ad4s3e.gz’ # also remote
# gunzip -dc ad4s3e.gz | ssh eedcoba@host ‘dd of=/dev/ad0s3e bs=1M’
# dd if=/dev/ad0 of=/dev/ad2 skip=1 seek=1 bs=4k conv=noerror # Skip MBR
# This is necessary if the destination (ad2) is smaller.
Recover
The command dd will read every single block of the partiton, even the blocks. In case of problems it is better to use the option conv=sync,noerror so dd will skip the bad block and write zeros at the destination. Accordingly it is important to set the block size equal or smaller than the disk block size. A 1k size seems safe, set it with bs=1k. If a disk has bad sectors and the data should be recovered from a partiton, create an image file with dd, mount the image and copy the content to a new disk. With the option noerror, dd will skip the bad sectors and write zeros instead, thus only the data contained in the bad sectors will be lost.
# dd if=/dev/hda of=/dev/null bs=1m # Check for bad blocks
# dd bs=1k if=/dev/hda1 conv=sync,noerror,notrunc | gzip | ssh \ # Send to remote
root@fry ‘dd of=hda1.gz bs=1k’
# dd bs=1k if=/dev/hda1 conv=sync,noerror,notrunc of=hda1.img # Store into an image
# mount -o loop /hda1.img /mnt # Mount the image
# rsync -ax /mnt/ /newdisk/ # Copy on a new disk
# dd if=/dev/hda of=/dev/hda # Refresh the magnetic state
# The above is useful to refresh a disk. It is perfectly safe, but must be unmounted.
Delete
# dd if=/dev/zero of=/dev/hdc # Delete full disk
# dd if=/dev/urandom of=/dev/hdc # Delete full disk better
# kill -USR1 PID # View dd progress (Linux only!)
MBR tricks
The MBR contains the boot loader and the partition table and is 512 bytes small. The first 446 are for the boot loader, the bytes 446 to 512 are for the partition table.
# dd if=/dev/sda of=/mbr_sda.bak bs=512 count=1 # Backup the full MBR
# dd if=/dev/zero of=/dev/sda bs=512 count=1 # Delete MBR and partiton table
# dd if=/mbr_sda.bak of=/dev/sda bs=512 count=1 # Restore the full MBR
# dd if=/mbr_sda.bak of=/dev/sda bs=446 count=1 # Restore only the boot loader
# dd if=/mbr_sda.bak of=/dev/sda bs=1 count=64 skip=446 seek=446 # Restore partition table
screen
Screen has two main functionalities:
* Run multiple terminal session within a single terminal.
* A started program is decoupled from the real terminal and can thus run in the background. The real terminal can be closed and reattached later.
Short start example
start screen with:
# screen
Within the screen session we can start a long lasting program (like top). Detach the terminal and reattach the same terminal from an other machine (over ssh for example).
# top
Now detach with Ctrl-a Ctrl-d. Reattach the terminal with
# screen -r
or better:
# screen -R -D
Attach here and now. In detail this means: If a session is running, then reattach. If necessary detach and logout remotely first. If it was not running create it and notify the user.
Screen commands (within screen)
All screen commands start with Ctrl-a.
* Ctrl-a ? help and summary of functions
* Ctrl-a c create an new window (terminal)
* Ctrl-a Ctrl-n and Ctrl-a Ctrl-p to switch to the next or previous
window in the list, by number.
* Ctrl-a Ctrl-N where N is a number from 0 to 9, to switch to the corresponding window.
* Ctrl-a ” to get a navigable list of running windows
* Ctrl-a a to clear a missed Ctrl-a
* Ctrl-a Ctrl-d to disconnect and leave the session running in the background
* Ctrl-a x lock the screen terminal with a password
The screen session is terminated when the program within the running terminal is closed and you logout from the terminal.
Find
Some important options:
* -x (on BSD) -xdev (on Linux) Stay on the same file system (dev in fstab).
* -exec cmd {} \; Execute the command and replace {} with the full path
* -iname Like -name but is case insensitive
* -ls Display information about the file (like ls -la)
* -size n n is +-n (k M G T P)
* -cmin n File’s status was last changed n minutes ago.
# find . -type f ! -perm -444 # Find files not readable by all
# find . -type d ! -perm -111 # Find dirs not accessible by all
# find /home/user/ -cmin 10 -print # Files created or modified in the last 10 min.
# find . -name ‘*.[ch]‘ | xargs grep -E ‘expr’ # Search ‘expr’ in this dir and below.
# find / -name “*.core” | xargs rm # Find core dumps and delete them (also try core.*)
# find / -name “*.core” -print -exec rm {} \; # Other syntax
# Find images and create an archive, iname is not case sensitive. -r for append
# find . \( -iname “*.png” -o -iname “*.jpg” \) -print -exec tar -rf images.tar {} \;
# find . -type f -name “*.txt” ! -name README.txt -print # Exclude README.txt files
# find /var/ -size +10M -exec ls -lh {} \; # Find large files > 10 MB
# find /var/ -size +10M -ls # This is simpler
# find . -size +10M -size -50M -print
# find /usr/ports/ -name work -type d -print -exec rm -rf {} \; # Clean the ports
# Find files with SUID; those file are vulnerable and must be kept secure
# find / -type f -user root -perm -4000 -exec ls -l {} \;
Be careful with xarg or exec as it might or might not honor quotings and can return wrong results when files or directories contain spaces. In doubt use “-print0 | xargs -0″ instead of “| xargs”. The option -print0 must be the last in the find command. See this nice mini tutorial for findhttp://www.hccfl.edu/pollock/Unix/FindCmd.htm.
# find . -type f | xargs ls -l # Will not work with spaces in names
# find . -type f -print0 | xargs -0 ls -l # Will work with spaces in names
# find . -type f -exec ls -l ‘{}’ \; # Or use quotes ‘{}’ with -exec
Miscellaneous
# which command # Show full path name of command
# time command # See how long a command takes to execute
# time cat # Use time as stopwatch. Ctrl-c to stop
# set | grep $USER # List the current environment
# cal -3 # Display a three month calendar
# date [-u|--utc|--universal] [MMDDhhmm[[CC]YY][.ss]]
# date 10022155 # Set date and time
# whatis grep # Display a short info on the command or word
# whereis java # Search path and standard directories for word
# setenv varname value # Set env. variable varname to value (csh/tcsh)
# export varname=”value” # set env. variable varname to value (sh/ksh/bash)
# pwd # Print working directory
# mkdir -p /path/to/dir # no error if existing, make parent dirs as needed
# mkdir -p project/{bin,src,obj,doc/{html,man,pdf},debug/some/more/dirs}
# rmdir /path/to/dir # Remove directory
# rm -rf /path/to/dir # Remove directory and its content (force)
# cp -la /dir1 /dir2 # Archive and hard link files instead of copy
# cp -lpR /dir1 /dir2 # Same for FreeBSD
# cp unixtoolbox.xhtml{,.bak} # Short way to copy the file with a new extension
# mv /dir1 /dir2 # Rename a directory
Install Software
List installed packages
# rpm -qa # List installed packages (RH, SuSE, RPM based)
# dpkg -l # Debian, Ubuntu
# pkg_info # FreeBSD list all installed packages
# pkg_info -W smbd # FreeBSD show which package smbd belongs to
# pkginfo # Solaris
Add/remove software
Front ends: yast2/yast for SuSE, redhat-config-packages for Red Hat.
# rpm -i pkgname.rpm # install the package (RH, SuSE, RPM based)
# rpm -e pkgname # Remove package
Debian
# apt-get update # First update the package lists
# apt-get install emacs # Install the package emacs
# dpkg –remove emacs # Remove the package emacs
# dpkg -S file # find what package a file belongs to
Gentoo
Gentoo uses emerge as the heart of its “Portage” package management system.
# emerge –sync # First sync the local portage tree
# emerge -u packagename # Install or upgrade a package
# emerge -C packagename # Remove the package
# revdep-rebuild # Repair dependencies
Solaris
The
# pkgadd -d
# pkgadd -d SUNWgtar # Add downloaded package (bunzip2 first)
# pkgrm SUNWgtar # Remove the package
FreeBSD
# pkg_add -r rsync # Fetch and install rsync.
# pkg_delete /var/db/pkg/rsync-xx # Delete the rsync package
Set where the packages are fetched from with the PACKAGESITE variable. For example:
# export PACKAGESITE=ftp://ftp.freebsd.org/pub/FreeBSD/ports/i386/packages/Latest/
# or ftp://ftp.freebsd.org/pub/FreeBSD/ports/i386/packages-6-stable/Latest/
FreeBSD ports
The port tree /usr/ports/ is a collection of software ready to compile and install. The ports are updated with the program portsnap.
# portsnap fetch extract # Create the tree when running the first time
# portsnap fetch update # Update the port tree
# cd /usr/ports/net/rsync/ # Select the package to install
# make install distclean # Install and cleanup (also see man ports)
# make package # Make a binary package for the port
Library path
Due to complex dependencies and runtime linking, programs are difficult to copy to an other system or distribution. However for small programs with little dependencies, the missing libraries can be copied over. The runtime libraries (and the missing one) are checked with ldd and managed with ldconfig.
# ldd /usr/bin/rsync # List all needed runtime libraries
# ldconfig -n /path/to/libs/ # Add a path to the shared libraries directories
# ldconfig -m /path/to/libs/ # FreeBSD
# LD_LIBRARY_PATH # The variable set the link library path
Convert Media
Sometimes one simply need to convert a video, audio file or document to another format.
Text encoding
Text encoding can get totally wrong, specially when the language requires
special characters like àäç. The command iconv can convert from
one encoding to an other.
# iconv -f
# iconv -f ISO8859-1 -t UTF-8 -o file.input > file_utf8
# iconv -l # List known coded character sets
Without the -f option, iconv will use the local char-set, which is usually fine
if the document displays well.
Unix - DOS newlines
Convert DOS (CR/LF) to Unix (LF) newlines within a Unix shell. See also dos2unix and unix2dos if you have them.
# sed ’s/.$//’ dosfile.txt > unixfile.txt
Convert Unix to DOS newlines within a Windows environment. Use sed from mingw or cygwin.
# sed -n p unixfile.txt > dosfile.txt
PDF to Jpeg and concatenate PDF files
Convert a PDF document with gs (GhostScript) to jpeg (or png) images for each page. Also much shorter with convert (from ImageMagick or GraphicsMagick).
# gs -dBATCH -dNOPAUSE -sDEVICE=jpeg -r150 -dTextAlphaBits=4 -dGraphicsAlphaBits=4 \
-dMaxStripSize=8192 -sOutputFile=unixtoolbox_%d.jpg unixtoolbox.pdf
# convert unixtoolbox.pdf unixtoolbox-%03d.png
# convert *.jpeg images.pdf # Create a simple PDF with all pictures
Ghostscript can also concatenate multiple pdf files into a single one. This only works well if the PDF files are “well behaved”.
# gs -q -sPAPERSIZE=a4 -dNOPAUSE -dBATCH -sDEVICE=pdfwrite -sOutputFile=all.pdf \
file1.pdf file2.pdf … # On Windows use ‘#’ instead of ‘=’
Convert video
Compress the Canon digicam video with an mpeg4 codec and repair the crappy sound.
# mencoder -o videoout.avi -oac mp3lame -ovc lavc -srate 11025 \
-channels 1 -af-adv force=1 -lameopts preset=medium -lavcopts \
vcodec=msmpeg4v2:vbitrate=600 -mc 0 vidoein.AVI
See sox for sound processing.
Copy an audio cd
The program cdparanoiahttp://xiph.org/paranoia/ can save the audio tracks (FreeBSD port in audio/cdparanoia/), oggenc can encode in Ogg Vorbis format, lame converts to mp3.
# cdparanoia -B # Copy the tracks to wav files in current dir
# lame -b 256 in.wav out.mp3 # Encode in mp3 256 kb/s
# for i in *.wav; do lame -b 256 $i `basename $i .wav`.mp3; done
# oggenc in.wav -b 256 out.ogg # Encode in Ogg Vorbis 256 kb/s
Printing
Print with lpr
# lpr unixtoolbox.ps # Print on default printer
# export PRINTER=hp4600 # Change the default printer
# lpr -Php4500 #2 unixtoolbox.ps # Use printer hp4500 and print 2 copies
# lpr -o Duplex=DuplexNoTumble … # Print duplex along the long side
# lpr -o PageSize=A4,Duplex=DuplexNoTumble …
# lpq # Check the queue on default printer
# lpq -l -Php4500 # Queue on printer hp4500 with verbose
# lprm - # Remove all users jobs on default printer
# lprm -Php4500 3186 # Remove job 3186. Find job nbr with lpq
# lpc status # List all available printers
# lpc status hp4500 # Check if printer is online and queue length
Some devices are not postscript and will print garbage when fed with a pdf file. This might be solved with:
# gs -dSAFER -dNOPAUSE -sDEVICE=deskjet -sOutputFile=\|lpr file.pdf
Databases
PostgreSQL
Change root or a username password
# psql -d template1 -U pgsql
> alter user pgsql with password ‘pgsql_password’; # Use username instead of “pgsql”
Create user and database
The commands createuser, dropuser, createdb and dropdb are convenient shortcuts equivalent to the SQL commands. The new user is bob with database bobdb ; use as root with pgsql the database super user:
# createuser -U pgsql -P bob # -P will ask for password
# createdb -U pgsql -O bob bobdb # new bobdb is owned by bob
# dropdb bobdb # Delete database bobdb
# dropuser bob # Delete user bob
The general database authentication mechanism is configured in pg_hba.conf
Grant remote access
The file $PGSQL_DATA_D/postgresql.conf specifies the address to bind to. Typically listen_addresses = ‘*’ for Postgres 8.x.
The file $PGSQL_DATA_D/pg_hba.conf defines the access control. Examples:
# TYPE DATABASE USER IP-ADDRESS IP-MASK METHOD
host bobdb bob 212.117.81.42 255.255.255.255 password
host all all 0.0.0.0/0 password
Backup and restore
The backups and restore are done with the user pgsql or postgres. Backup and restore a single database:
# pg_dump –clean dbname > dbname_sql.dump
# psql dbname <>
Backup and restore all databases (including users):
# pg_dumpall –clean > full.dump
# psql -f full.dump postgres
In this case the restore is started with the database postgres which is better when reloading an empty cluster.
MySQL
Change mysql root or username password
Method 1
# /etc/init.d/mysql stop
or
# killall mysqld
# mysqld –skip-grant-tables
# mysqladmin -u root password ‘newpasswd’
# /etc/init.d/mysql start
Method 2
# mysql -u root mysql
mysql> UPDATE USER SET PASSWORD=PASSWORD(”newpassword”) where user=’root’;
mysql> FLUSH PRIVILEGES; # Use username instead of “root”
mysql> quit
Create user and database
# mysql -u root mysql
mysql> CREATE DATABASE bobdb;
mysql> GRANT ALL ON *.* TO ‘bob’@'%’ IDENTIFIED BY ‘pwd’; # Use localhost instead of %
# to restrict the network access
mysql> DROP DATABASE bobdb; # Delete database
mysql> DROP USER bob; # Delete user
mysql> DELETE FROM mysql.user WHERE user=’bob and host=’hostname’; # Alt. command
mysql> FLUSH PRIVILEGES;
Grant remote access
Remote access is typically permitted for a database, and not all databases. The file /etc/my.cnf contains the IP address to bind to. Typically comment the line bind-address = out.
# mysql -u root mysql
mysql> GRANT ALL ON bobdb.* TO bob@’xxx.xxx.xxx.xxx’ IDENTIFIED BY ‘PASSWORD’;
mysql> REVOKE GRANT OPTION ON foo.* FROM bar@’xxx.xxx.xxx.xxx’;
mysql> FLUSH PRIVILEGES; # Use ‘hostname’ or also ‘%’ for full access
Backup and restore
Backup and restore a single database:
# mysqldump -u root -psecret –add-drop-database dbname > dbname_sql.dump
# mysql -u root -psecret -D dbname <>
Backup and restore all databases:
# mysqldump -u root -psecret –add-drop-database –all-databases > full.dump
# mysql -u root -psecret <>
Here is “secret” the mysql root password, there is no space after -p. When the -p option is used alone (w/o password), the password is asked at the command prompt.
SQLite
SQLitehttp://www.sqlite.org is a small powerfull self-contined, serverless, zero-configuration SQL database.
Dump and restore
It can be useful to dump and restore an SQLite database. For example you can edit the dump file to change a column attribute or type and then restore the database. This is easier than messing with SQL commands. Use the command sqlite3 for a 3.x database.
# sqlite database.db .dump > dump.sql # dump
# sqlite database.db <>
Convert 2.x to 3.x database
sqlite database_v2.db .dump | sqlite3 database_v3.db
Disk Quota
A disk quota allows to limit the amount of disk space and/or the number of files a user or (or member of group) can use. The quotas are allocated on a per-file system basis and are enforced by the kernel.
Linux setup
The quota tools package usually needs to be installed, it contains the command line tools.
Activate the user quota in the fstab and remount the partition. If the partition is busy, either all locked files must be closed, or the system must be rebooted. Add usrquota to the fstab mount options, for example:
/dev/sda2 /home reiserfs rw,acl,user_xattr,usrquota 1 1
# mount -o remount /home
# mount # Check if usrquota is active, otherwise reboot
Initialize the quota.user file with quotacheck.
# quotacheck -vum /home
# chmod 644 /home/aquota.user # To let the users check their own quota
Activate the quota either with the provided script (e.g. /etc/init.d/quotad on SuSE) or with quotaon:
quotaon -vu /home
Check that the quota is active with:
quota -v
FreeBSD setup
The quota tools are part of the base system, however the kernel needs the option quota. If it is not there, add it and recompile the kernel.
options QUOTA
As with Linux, add the quota to the fstab options (userquota, not usrquota):
/dev/ad0s1d /home ufs rw,noatime,userquota 2 2
# mount /home # To remount the partition
Enable disk quotas in /etc/rc.conf and start the quota.
# grep quotas /etc/rc.conf
enable_quotas=”YES” # turn on quotas on startup (or NO).
check_quotas=”YES” # Check quotas on startup (or NO).
# /etc/rc.d/quota start
Assign quota limits
The quotas are not limited per default (set to 0). The limits are set with edquota for single users. A quota can be also duplicated to many users. The file structure is different between the quota implementations, but the principle is the same: the values of blocks and inodes can be limited. Only change the values of soft and hard. If not specified, the blocks are 1k. The grace period is set with edquota -t. For example:
# edquota -u colin
Linux
Disk quotas for user colin (uid 1007):
Filesystem blocks soft hard inodes soft hard
/dev/sda8 108 1000 2000 1 0 0
FreeBSD
Quotas for user colin:
/home: kbytes in use: 504184, limits (soft = 700000, hard = 800000)
inodes in use: 1792, limits (soft = 0, hard = 0)
For many users
The command edquota -p is used to duplicate a quota to other users. For example to duplicate a reference quota to all users:
# edquota -p refuser `awk -F: ‘$3 > 499 {print $1}’ /etc/passwd`
# edquota -p refuser user1 user2 # Duplicate to 2 users
Checks
Users can check their quota by simply typing quota (the file quota.user must be readable). Root can check all quotas.
# quota -u colin # Check quota for a user
# repquota /home # Full report for the partition for all users
Shells
Most Linux distributions use the bash shell while the BSDs use tcsh, the bourne shell is only used for scripts. Filters are very useful and can be piped:
* grep Pattern matching
* sed Search and Replace strings or characters
* cut Print specific columns from a marker
* sort Sort alphabetically or numerically
* uniq Remove duplicate lines from a file
For example used all at once:
# ifconfig | sed ’s/ / /g’ | cut -d” ” -f1 | uniq | grep -E “[a-z0-9]+” | sort -r
# ifconfig | sed ‘/.*inet addr:/!d;s///;s/ .*//’|sort -t. -k1,1n -k2,2n -k3,3n -k4,4n
The first character in the sed pattern is a tab. To write a tab on the console, use ctrl-v ctrl-tab.
bash
Redirects and pipes for bash and sh:
# cmd 1> file # Redirect stdout to file.
# cmd 2> file # Redirect stderr to file.
# cmd 1>> file # Redirect and append stdout to file.
# cmd &> file # Redirect both stdout and stderr to file.
# cmd >file 2>&1 # Redirects stderr to stdout and then to file.
# cmd1 | cmd2 # pipe stdout to cmd2
# cmd1 2>&1 | cmd2 # pipe stdout and stderr to cmd2
Modify your configuration in ~/.bashrc (it can also be ~/.bash_profile). The following entries are useful, reload with “. .bashrc”.
# in .bashrc
bind ‘”\e[A"':history-search-backward # Use up and down arrow to search
bind '"\e[B"':history-search-forward # the history. Invaluable!
set -o emacs # Set emacs mode in bash (see below)
set bell-style visible # Do not beep, inverse colors
# Set a nice prompt like [user@host]/path/todir>
PS1=”\[\033[1;30m\][\[\033[1;34m\]\u\[\033[1;30m\]”
PS1=”$PS1@\[\033[0;33m\]\h\[\033[1;30m\]]\[\033[0;37m\]”
PS1=”$PS1\w\[\033[1;30m\]>\[\033[0m\]”
# To check the currently active aliases, simply type alias
alias ls=’ls -aF’ # Append indicator (one of */=>@|)
alias ll=’ls -aFls’ # Listing
alias la=’ls -all’
alias ..=’cd ..’
alias …=’cd ../..’
export HISTFILESIZE=5000 # Larger history
export CLICOLOR=1 # Use colors (if possible)
export LSCOLORS=ExGxFxdxCxDxDxBxBxExEx
tcsh
Redirects and pipes for tcsh and csh (simple > and >> are the same as sh):
# cmd >& file # Redirect both stdout and stderr to file.
# cmd >>& file # Append both stdout and stderr to file.
# cmd1 | cmd2 # pipe stdout to cmd2
# cmd1 |& cmd2 # pipe stdout and stderr to cmd2
The settings for csh/tcsh are set in ~/.cshrc, reload with “source .cshrc”. Examples:
# in .cshrc
alias ls ‘ls -aF’
alias ll ‘ls -aFls’
alias la ‘ls -all’
alias .. ‘cd ..’
alias … ‘cd ../..’
set prompt = “%B%n%b@%B%m%b%/> ” # like user@host/path/todir>
set history = 5000
set savehist = ( 6000 merge )
set autolist # Report possible completions with tab
set visiblebell # Do not beep, inverse colors
# Bindkey and colors
bindkey -e Select Emacs bindings # Use emacs keys to edit the command prompt
bindkey -k up history-search-backward # Use up and down arrow to search
bindkey -k down history-search-forward
setenv CLICOLOR 1 # Use colors (if possible)
setenv LSCOLORS ExGxFxdxCxDxDxBxBxExEx
The emacs mode enables to use the emacs keys shortcuts to modify the command prompt line. This is extremely useful (not only for emacs users). The most used commands are:
* C-a Move cursor to beginning of line
* C-e Move cursor to end of line
* M-b Move cursor back one word
* M-f Move cursor forward one word
* M-d Cut the next word
* C-w Cut the last word
* C-u Cut everything before the cursor
* C-k Cut everything after the cursor (rest of the line)
* C-y Paste the last thing to be cut (simply paste)
* C-_ Undo
Note: C- = hold control, M- = hold meta (which is usually the alt or escape key).
Scripting
Basics | Script example | sed | Regular Expressions | useful commands
The Bourne shell (/bin/sh) is present on all Unix installations and scripts written in this language are (quite) portable; man 1 sh is a good reference.
Basics
Variables and arguments
Assign with variable=value and get content with $variable
MESSAGE=”Hello World” # Assign a string
PI=3.1415 # Assign a decimal number
N=8
TWON=`expr $N * 2` # Arithmetic expression (only integers)
TWON=$(($N * 2)) # Other syntax
TWOPI=`echo “$PI * 2″ | bc -l` # Use bc for floating point operations
ZERO=`echo “c($PI/4)-sqrt(2)/2″ | bc -l`
The command line arguments are
$0, $1, $2, … # $0 is the command itself
$# # The number of arguments
$* # All arguments (also $@)
Special Variables
$$ # The current process ID
$? # exit status of last command
command
if [ $? != 0 ]; then
echo “command failed”
fi
mypath=`pwd`
mypath=${mypath}/file.txt
echo ${mypath##*/} # Display the filename only
echo ${mypath%%.*} # Full path without extention
var2=${var:=string} # Use var if set, otherwise use string
# assign string to var and then to var2.
Constructs
for file in `ls`
do
echo $file
done
count=0
while [ $count -lt 5 ]; do
echo $count
sleep 1
count=$(($count + 1))
done
myfunction() {
find . -type f -name “*.$1″ -print # $1 is first argument of the function
}
myfunction “txt”
Generate a file
MYHOME=/home/colin
cat > testhome.sh << _EOF
# All of this goes into the file testhome.sh
if [ -d "$MYHOME" ] ; then
echo $MYHOME exists
else
echo $MYHOME does not exist
fi
_EOF
sh testhome.sh
Bourne script example
As a small example, the script used to create a PDF booklet from this xhtml document:
#!/bin/sh
# This script creates a book in pdf format ready to print on a duplex printer
if [ $# -ne 1 ]; then # Check the argument
echo 1>&2 “Usage: $0 HtmlFile”
exit 1 # non zero exit if error
fi
file=$1 # Assign the filename
fname=${file%.*} # Get the name of the file only
fext=${file#*.} # Get the extension of the file
prince $file -o $fname.pdf # from www.princexml.com
pdftops -paper A4 -noshrink $fname.pdf $fname.ps # create postscript booklet
cat $fname.ps |psbook|psnup -Pa4 -2 |pstops -b “2:0,1U(21cm,29.7cm)” > $fname.book.ps
ps2pdf13 -sPAPERSIZE=a4 -sAutoRotatePages=None $fname.book.ps $fname.book.pdf
# use #a4 and #None on Windows!
exit 0 # exit 0 means successful
Some sed commands
Here is the one liner gold minehttp://student.northpark.edu/pemente/sed/sed1line.txt. And a good introduction and tutorial to sedhttp://www.grymoire.com/Unix/Sed.html.
sed ’s/string1/string2/g’ # Replace string1 with string2
sed -i ’s/wroong/wrong/g’ *.txt # Replace a recurring word with g
sed ’s/\(.*\)1/\12/g’ # Modify anystring1 to anystring2
sed ‘/
/,/<\/p>/d’ t.xhtml # Delete lines that start with
# and end with
sed ‘/ *#/d; /^ *$/d’ # Remove comments and blank lines
sed ’s/[ \t]*$//’ # Remove trailing spaces (use tab as \t)
sed ’s/^[ \t]*//;s/[ \t]*$//’ # Remove leading and trailing spaces
sed ’s/[^*]/[&]/’ # Enclose first char with [] top->[t]op
sed = file | sed ‘N;s/\n/\t/’ > file.num # Number lines on a file
Regular Expressions
Some basic regular expression useful for sed too. See Basic Regex Syntaxhttp://www.regular-expressions.info/reference.html for a good primer.
[\^$.|?*+() # special characters any other will match themselves
\ # escapes special characters and treat as literal
* # repeat the previous item zero or more times
. # single character except line break characters
.* # match zero or more characters
^ # match at the start of a line/string
$ # match at the end of a line/string
.$ # match a single character at the end of line/string
^ $ # match line with a single space
[^A-Z] # match any line beginning with any char from A to Z
Some useful commands
The following commands are useful to include in a script or as one liners.
sort -t. -k1,1n -k2,2n -k3,3n -k4,4n # Sort IPv4 ip addresses
echo ‘Test’ | tr ‘[:lower:]‘ ‘[:upper:]‘ # Case conversion
echo foo.bar | cut -d . -f 1 # Returns foo
PID=$(ps | grep script.sh | grep bin | awk ‘{print $1}’) # PID of a running script
PID=$(ps axww | grep [p]ing | awk ‘{print $1}’) # PID of ping (w/o grep pid)
IP=$(ifconfig $INTERFACE | sed ‘/.*inet addr:/!d;s///;s/ .*//’) # Linux
IP=$(ifconfig $INTERFACE | sed ‘/.*inet /!d;s///;s/ .*//’) # FreeBSD
if [ `diff file1 file2 | wc -l` != 0 ]; then [...] fi # File changed?
cat /etc/master.passwd | grep -v root | grep -v \*: | awk -F”:” \ # Create http passwd
‘{ printf(”%s:%s\n”, $1, $2) }’ > /usr/local/etc/apache2/passwd
testuser=$(cat /usr/local/etc/apache2/passwd | grep -v \ # Check user in passwd
root | grep -v \*: | awk -F”:” ‘{ printf(”%s\n”, $1) }’ | grep ^user$)
:(){ :|:& };: # bash fork bomb. Will kill your machine
tail +2 file > file2 # remove the first line from file
I use this little trick to change the file extension for many files at once. For example from .cxx to .cpp. Test it first without the | sh at the end. You can also do this with the command rename if installed. Or with bash builtins.
# ls *.cxx | awk -F. ‘{print “mv “$0″ “$1″.cpp”}’ | sh
# ls *.c | sed “s/.*/cp & &.$(date “+%Y%m%d”)/” | sh # e.g. copy *.c to *.c.20080401
# rename .cxx .cpp *.cxx # Rename all .cxx to cpp
# for i in *.cxx; do mv $i ${i%%.cxx}.cpp; done # with bash builtins
Programming
C basics
strcpy(newstr,str) /* copy str to newstr */
expr1 ? expr2 : expr3 /* if (expr1) expr2 else expr3 */
x = (y > z) ? y : z; /* if (y > z) x = y; else x = z; */
int a[]={0,1,2}; /* Initialized array (or a[3]={0,1,2}; */
int a[2][3]={{1,2,3},{4,5,6}}; /* Array of array of ints */
int i = 12345; /* Convert in i to char str */
char str[10];
sprintf(str, “%d”, i);
C example
A minimal c program simple.c:
#include
main() {
int number=42;
printf(”The answer is %i\n”, number);
}
Compile with:
# gcc simple.c -o simple
# ./simple
The answer is 42
C++ basics
*pointer // Object pointed to by pointer
&obj // Address of object obj
obj.x // Member x of class obj (object obj)
pobj->x // Member x of class pointed to by pobj
// (*pobj).x and pobj->x are the same
C++ example
As a slightly more realistic program in C++, let’s create a class in its own header (IPv4.h) and implementation (IPv4.cpp) and create a program which uses the class functionality. The class has a member to convert an IP address in integer format to the known quad format. This is a minimal c++ program with a class and multi-source compile.
IPv4 class
IPv4.h:
#ifndef IPV4_H
#define IPV4_H
#include
namespace GenericUtils { // create a namespace
class IPv4 { // class definition
public:
IPv4();
~IPv4();
std::string IPint_to_IPquad(unsigned long ip);// member interface
};
} //namespace GenericUtils
#endif // IPV4_H
IPv4.cpp:
#include “IPv4.h”
#include
#include
using namespace std; // use the namespaces
using namespace GenericUtils;
IPv4::IPv4() {} // default constructor/destructor
IPv4::~IPv4() {}
string IPv4::IPint_to_IPquad(unsigned long ip) { // member implementation
ostringstream ipstr; // use a stringstream
ipstr << ((ip &0xff000000) >> 24) // Bitwise right shift
<< “.” << ((ip &0×00ff0000) >> 16)
<< “.” << ((ip &0×0000ff00) >> 8)
<< “.” << ((ip &0×000000ff));
return ipstr.str();
}
The program simplecpp.cpp
#include “IPv4.h”
#include
#include
using namespace std;
int main (int argc, char* argv[]) {
string ipstr; // define variables
unsigned long ipint = 1347861486; // The IP in integer form
GenericUtils::IPv4 iputils; // create an object of the class
ipstr = iputils.IPint_to_IPquad(ipint); // call the class member
cout <<>
return 0;
}
Compile and execute with:
# g++ -c IPv4.cpp simplecpp.cpp # Compile in objects
# g++ IPv4.o simplecpp.o -o simplecpp.exe # Link the objects to final executable
# ./simplecpp.exe
1347861486 = 80.86.187.238
Use ldd to check which libraries are used by the executable and where they are located. This command is also used to check if a shared library is missing or if the executable is static.
# ldd /sbin/ifconfig
Simple Makefile
The corresponding minimal Makefile for the multi-source program is shown below. The lines with instructions must begin with a tab! The back slash “\” can be used to cut long lines.
CC = g++
CFLAGS = -O
OBJS = IPv4.o simplecpp.o
simplecpp: ${OBJS}
${CC} -o simplecpp ${CFLAGS} ${OBJS}
clean:
rm -f ${TARGET} ${OBJS}